分享
ASTM_E_1146_-_08.pdf
下载文档

ID:168491

大小:61.04KB

页数:2页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_E_1146_ _08
Designation:E114608Standard Specification forMuriatic Acid(Technical Grade Hydrochloric Acid)1This standard is issued under the fixed designation E1146;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1.Scope*1.1 This specification covers muriatic acid,also known astechnical grade hydrochloric acid.1.2 This specification includes requirements for muriaticacid available commercially in 20 Baum and 22 Baumconcentration grades.1.3 The values stated in SI units are to be regarded asstandard.The values given in parentheses are for informationonly.1.4 Review the current Material Safety Data Sheets(MSDS)for detailed information concerning toxicity,first aidprocedures,handling and safety precautions.1.5 The following safety hazards caveat pertains only to thetest methods portion,Section 5:This standard does not purportto address all of the safety concerns,if any,associated with itsuse.It is the responsibility of the user of this standard toestablish appropriate safety and health practices and deter-mine the applicability of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2E224 Test Methods for Analysis of Hydrochloric AcidE300 Practice for Sampling Industrial Chemicals3.Requirements3.1 Muriatic acid shall conform to the following chemicaland physical requirements:20 Baum22 BaumTotal acidity as HCl,%mass(m/m)(%by weight)30.71 to 32.9335.02 to 37.14Fe,g/g(ppm)5 max5 maxBaum gravity at 15.5/15.5C19.60 to 20.8021.90 to 23.004.Sampling4.1 Sample muriatic acid in accordance with the appropriatesections of Practice E300 for simple liquids.4.2 Take composite sample of not less than 1 L.5.Test Methods5.1 Determine the requirements as specified in 3.1 using thetest procedures described in Test Methods E224.6.Keywords6.1 muriatic acid;technical grade hydrochloric acid1This specification is under the jurisdiction of ASTM Committee E15 onIndustrial and Specialty Chemicals and is the direct responsibility of SubcommitteeE15.02 on Product Standards.Current edition approved April 1,2008.Published May 2008.Originallyapproved in 1987.Last previous edition approved in 2002 as E114697(2002).DOI:10.1520/E1146-08.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 SUMMARY OF CHANGESCommittee E15 has identified the location of selected changes to this standard since the last issue(E114697(2002)that may impact the use of this standard.(1)Updated units of measure to comply with the InternationalSystem of Units(SI).(2)Added subsection to Scope stating that the SI units areconsidered standard.(3)Added Summary of Changes section.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.Users of this standard are expressly advised that determination of the validity of any such patent rights,and the riskof infringement of such rights,are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised,either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters.Your comments will receive careful consideration at a meeting of theresponsible technical committee,which you may attend.If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards,at the address shown below.This standard is copyrighted by ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.Individual reprints(single or multiple copies)of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585(phone),610-832-9555(fax),or serviceastm.org(e-mail);or through the ASTM website(www.astm.org).Permission rights to photocopy the standard may also be secured from the ASTM website(www.astm.org/COPYRIGHT/).E1146 082

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开