分享
ASTM_D_994_-_D_994M_-_11_2022.pdf
下载文档

ID:168384

大小:147.31KB

页数:4页

格式:PDF

时间:2023-03-04

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
TM_D_994_ _D_994M_ _11_2022
Designation:D994/D994M11(Reapproved 2022)Standard Specification forPreformed Expansion Joint Filler for Concrete(BituminousType)1This standard is issued under the fixed designation D994/D994M;the number immediately following the designation indicates the yearof original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification covers bituminous preformed expan-sion joint filler for use in concrete construction.NOTE1Attention is called to ASTM Specifications D1751 andD1752.1.2 UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard.Thevalues stated in each system may not be exact equivalents;therefore,each system shall be used independently of the other.Combining values from the two systems may result in noncon-formance with the standard.1.3 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C670 Practice for Preparing Precision and Bias Statementsfor Test Methods for Construction MaterialsD545 Test Methods for Preformed Expansion Joint Fillersfor Concrete Construction(Nonextruding and ResilientTypes)D1751 Specification for Preformed Expansion Joint Fillerfor Concrete Paving and Structural Construction(Nonex-truding and Resilient Bituminous Types)D1752 Specification for Preformed Sponge Rubber,Corkand Recycled PVC Expansion Joint Fillers for ConcretePaving and Structural Construction3.Manufacture3.1 This product shall consist of a bituminous(asphalt ortar)mastic composition,formed and encased between twolayers of bituminous impregnated felt or two layers of glass-fiber felt.The mastic shall comprise mineral fillers andreinforcing fibers and may contain thin strips of reinforcingsheet material.4.General Requirements4.1 Preformed strips of expansion joint filler shall be of suchcharacter as not to be deformed or broken by ordinary handlingwhen exposed to atmospheric conditions and shall not becomebrittle in cold weather.Pieces of the joint filler that have beendamaged shall be rejected.5.Properties5.1 Distortion at 50 C 125 FThe joint filler shall notshow a deflection of more than 1 in.25 mm when tested inaccordance with 8.2.1.5.2 BrittlenessThe joint filler shall not crack or shatterwhen tested in accordance with 8.2.2.NOTE2Expansion joint filler having a nominal thickness of 5 mm14in.or less shall not be subject to a requirement for brittleness.5.3 Water AbsorptionThe water absorption of the jointfiller,when tested in accordance with 8.2.3,shall not exceedthe following values:Nominal Thickness ofJoint,min,mm in.Absorption,max,weight%25 12.520 34315 12410 385NOTE3Expansion joint filler having a nominal thickness of less than10 mm 38in.shall not be subject to a requirement for water absorption.5.4 CompressionThe load required to compress the testspecimen to 50%of its thickness before test shall not be lessthan nor more than the following values when the joint filler istested in accordance with 8.2.4.Nominal Thickness of Joint,mm in.Load Requirements,minmax.kPa psi25 17005000 10075420 347006000 10084115 127006500 1009281This specification is under the jurisdiction of ASTM Committee D04 on Roadand Paving Materials and is the direct responsibility of Subcommittee D04.34 onPreformed Joint Fillers,Sealers and Sealing Systems.Current edition approved June 1,2022.Published June 2022.Originallyapproved in 1948.Last previous edition approved in 2016 as D994/D994M 11(2016).DOI:10.1520/D0994_D0994M-11R22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1NOTE4Expansion joint filler having a nominal thickness of less than15 mm 12in.shall not be subject to a requirement for compression.6.Dimensions and Permissible Variations6.1 The preformed strips shall conform to the dimensionsspecified or shown on the plans.Strips of the joint filler that donot conform to the specified dimensions within the permissiblevariation

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开