ASME_Y14.1-2005.pdf

ASME Y14.1-2005(Revision of ASME Y14.1-1995)Decimal InchDrawing SheetSize and FormatEngineering Drawing and Related Documentation PracticesAN AMERICAN NATIONAL STANDARDThe American Society ofMechanical EngineersASME Y14.1ADOPTION NOTICEASME Y14.1,Decimal Inch Drawing Sheet Size and Format,was adopted on 10 March 1995 for use by theDepartment of Defense,DoD.Proposed changes by DoD activities must be submitted to the DoD AdoptingActivity:Commander,U.S.ARDEC,ATTN:AMSRD-AAR-AIS-SS,Picatinny Arsenal,NJ 07806-5000 or emailedto ardec-stdznpica.army.mil.Copies of this document may be purchased from the American Society of MechanicalEngineers(ASME),22 Law Drive,PO Box 2900,Fairfield,NJ 07007-2900;http:/www.asme.org.Custodians:Adopting Activity:Army-ARArmy-ARNavy-SAAir Force-16DLA-DHReview Activities:Army-CR,IE,PT,TM2Navy-AS,CG,CH,EC,NP,TD,YDAir Force-13Other-NS,MP,CM,DC2NOTE:The activities listed above were interested in this document as of the date of this document.Sinceorganizations and responsibilities can change,you should verify the currency of the information above usingthe ASSIST Online database at http:/assist.daps.dla.mil.AMSC N/AAREA DRPRDISTRIBUTION STATEMENT A.Approved for public release;distribution is unlimited.ASME Y14.1-2005(Revision of ASME Y14.1-1995)Decimal InchDrawing SheetSize and FormatEngineering Drawing and Related Documentation PracticesAN AMERICAN NATIONAL STANDARDThe American Society ofMechanical EngineersThree Park Avenue.New York,NY 10016Date of Issuance:May 15,2006This Standard will be revised when the Society approves the issuance of a new edition.There willbe no addenda or written interpretations of the requirements of this Standard issued to this edition.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American NationalStandards.The Standards Committee that approved the code or standard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participate.The proposed code or standard was madeavailable for public review and comment that provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not approve,rate,or endorseany item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with anyitems mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability forinfringement of any applicable letters patent,nor assumes any such liability.Users of a code or standard are expresslyadvised that determination of the validity of any such patent rights,and the risk of infringement of such rights,isentirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted asgovernment or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the establishedASME procedures and policies,which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright2006byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.CONTENTSForew0rdCommittee RosterviCorrespondence With the Y14 Committee.vii1 General1.1 Scope.112Purp0se113 Units11.4 Applicable Documents11.5 Definitions12 Drawing Sheet Sizes.221 Margins22.2 Drawing Sizes22.3 Computer-Generated Drawings.33f0 rmats,33.1B阳si33.2 Continuation Sheets.333B引0CkS33.4 Lettering335Zoning.33.6 Lines.43.7 Microfilm Alignment.4 Titte Btocks.41L0 cation44.2 Contents4.3 Continuation Sheet Title Block45Revision History Block.451L0cati0n5.2 Contents56 Revision Status of Sheets Block.57 Associated Lists.58 Additional Data Blocks.58.1 Angle of Projection Block.58.2 Dimensioning and Tolerancing Block.58.3 Application Block-Optional.59Additional Drawing Number Blocks.59.1 Margin Drawing Number Block-Optional.59.2 Roll Size Drawing Microfilm Identification Blocks.5Figures1 Flat Sheet Size Formats,A Through F Sizes.62 Roll Size Format,G Size.73 Roll Size Formats,H,J,and K Sizes.84 Title Block for A,B,C,and G Sizes.95 Title Block for D,E,E H,J,and K Sizes.96 Continuation Sheet Title Block for A,B,C,and G Sizes.107 Continuation Sheet Title Block for D,E,F,H,J,and K Sizes.10i试