ASME_Y14-41-2003.pdf

DIGITAL PRODUCTDEFINITION DATAPRACTICESASME Y14.41-2003DIGITAL PRODUCTDEFINITION DATAPRACTICESAn American National StandardEngineering Drawing and RelatedDocumentation PracticesEngineering Drawing and RelatedDocumentation PracticesAn American National StandardASME Y14.41-2003Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ASME Y14.41ADOPTION NOTICEASME Y14.41,Digital Product Definition Data Practices,was adopted on 7 July 2003 for use by the Departmentof Defense,(DoD).Proposed changes by DoD activities must be submitted to the DoD Adopting Activity:Com-mander,U.S.Army TACOM-ARDEC,ATTN:AMSTA-AR-QAW-E,Picatinny Arsenal,NJ 07806-5000.Copies ofthis document may be purchased from The American Society of Mechanical Engineers(ASME),22 Law Drive,PO Box 2900,Fairfield,NJ 07007-2900;http:/www.asme.org.Custodians:Adopting Activity:Army ARArmy ARNavy SAAir Force 16DLA DHReview Activities:Army AT,AV,CE,CR,EA,GL,MI,SM,TENavy AS,CH,EC,MC,OS,SH,TD,YDAir Force 11,13,19,68,70,71,84,99DLA CC,ISNSA NSAMSC N/AAREA DRPRDISTRIBUTION STATEMENT A.Approved for public release;distribution is unlimited.Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ANAMERICANNATIONALSTANDARDDIGITALPRODUCTDEFINITIONDATAPRACTICESASMEY14.41-2003Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.Date of Issuance:August 15,2003The next edition of this Standard is scheduled for publication in 2007.There will be no addenda orwritten interpretations of the requirements of this Standard issued to this edition.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American NationalStandards.The Standards Committee that approved the code or standard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participate.The proposed code or standard was madeavailable forpublic review andcomment thatprovides an opportunityfor additional publicinput from industry,academia,regulatory agencies,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with anyitems mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability forinfringement of any applicable letters patent,nor assumes any such liability.Users of a code or standard are expresslyadvised that determination of the validity of any such patent rights,and the risk of infringement of such rights,isentirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted asgovernment or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the establishedASME procedures and policies,which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright 2003 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.CONTENTSForeword.viCommittee Roster.vii1General.11.1Scope.11.2Structure of Standard.11.3Figures.11.4Reference to This Standard.11.5Units.11.6Text in Figures.11.7Symbols.11.8References.11.9Definitions and Terminology.22Data Set Identification and Control.22.1General.22.2Related Data.42.3Data Management.43Data Set Requirements.43.1General.43.2General Model Requirements.53.3General Method Requirements.73.4Management Data.73.5Security Marking.73.6Views on Models.94Design Model Requirements.104.1General.105Common Requirements for Product Definition Data.115.1Common Requirements.115.2Model Requirements.115.3Drawing Requirements.166Notes and Special Notations.266.1Common Requirements.266.2Model Requirements.266.3Drawing Requirements.277Model Values and Dimensions.277.1Common Requirements.277.2Model Requirements.287.3Drawing Requirements.298Plus and Minus Tolerances.308.1Common Requirements.308.2Model Requirements.308.3Drawing Requirement