14-5_Edtn_2009.pdf

AN INTERNATIO NAL STANDARDASME Y14.5-2009Revision of ASME Y14.5M-1994(R2004)Dimensioningand TolerancingEngineering Drawing and Related Documentation PracticesCopyright 2009 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ASME Y14.5ADOPTION NOTICEASME Y14.5,Dimensioning and Tolerancing,was adopted on 9 February 2009 for use by the Department ofDefense(DoD).ProposedchangesbyDoDactivitiesmustbesubmittedtotheDoDAdoptingActivity:Commander,U.S.Army Research,Development and Engineering Center(ARDEC),ATTN:AMSRD-AAR-QES-E,PicatinnyArsenal,NJ 07806-5000.Copies of this document may be purchased from The American Society of MechanicalEngineers(ASME),22 Law Drive,P.O.Box 2900,Fairfield,NJ 07007-2900,http:/www.asme.org.Custodians:Adopting Activity:Army ARArmy ARNavy SA(ProjectDRPR-2009-003)Air Force 16Review Activities:Army CR,IE,MI,PT,TM2Navy AS,CG,CH,EC,MC,NP,TDAir Force 13,99DLA DHOSD SENSA NSOther CM,MP,DC2NOTE:The activities listed above were interested in this document as of the dateof this document.Since organizations and responsibilities can change,you shouldverify the currency of the information above using the ASSIST Online databaseat http:/assist.daps.dla.mil.AMSC N/AAREA DRPRDISTRIBUTION STATEMENT A.Approved for public release;distribution is unlimited.Copyright 2009 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ASME Y14.5-2009Dimensioning and TolerancingEngineering Drawing and Related Documentation PracticesA N I N T E R N A T I O N A L S T A N D A R DRevision of ASME Y14.5M-1994(R2004)Copyright 2009 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.Date of Issuance:March 27,2009This Standard will be revised when the Society approves the issuance of a new edition.There will be no addenda or written interpretations of the requirements of this Standard issued to this edition.Periodically certain actions of the ASME Y14 Committee may be published as Cases.Cases are published on the ASME Web site under the Committee Pages at http:/cstools.asme.org as they are issued.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American National Standards.The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate.The proposed code or standard was made available for public review and comment that provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable letters patent,nor assumes any such liability.Users of a code or standard are expressly advised that determination of the validity of any such patent rights,and the risk of infringement of such rights,is entirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures and policies,which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright 2009 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.Copyright 2009 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 b