-35M_R2008_E1997.pdf

Copyright 1997 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.REAFFIRMED 2008FOR CURRENT COMMITTEE PERSONNELPLEASE E-MAIL CSasme.orgASME Y14.35M-1997 ASME Y14.35M-1997,Revision of Engineering Drawings and Associated Documents,was adopted on 20 October 1997 for use by the Department of Defense(DoD).Proposed changes by DoD activities must be submitted to the DoD Adopting Activity;Commander,US Army TACOM-ARDEC,ATTN:AMSTA-AR-EDE-S,Picatinny Arsenal,NJ 07806-5000.DoD activities may obtain copies of this Standard from the Standardization Document Order Desk,700 Robbins Avenue,Building 4D,Philadelphia,PA 191 1 1-5094.The private sector and other Government agencies may purchase copies from the American Society of Mechanical Engineers,345 East 47th Street,New York,NY 10017.Custodians:Army-AR Navy-SA Air Force-16 DLA-DH Adopting Activity:Army-AR(Project DRPR-0348)Review activities:Army-AAT,AV,CE,CR,EA.ER.GL,ME,MI,SC,SM,TE Navy-AS,CH,EC,MC,OS.SH,TD,YD-1 Air Force-1 1,13,19,68,70.7 1.79,80,84,90,99 DLA-CS,DH,GS,IS NSA-NS AMSC N/A AREA DRPR DISTRIBUTION STATEMENT A.Approved for public release;distribution is unlimited.Copyright 1997 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.The American Society of Mechanical Engineers REVISION OF ENGINEERING DRAWINGS AND ASSOCIATED DOIUMENTS ASME Y 14.35M-1 flu7(Revision of ASME Y 14.351-1 992)Copyright 1997 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.Date of Issuance:December 8,1997 This Standard will be revised when the Society approves the issuance of a new edition.There will be no addenda or written interpretations of the re-quirements of this Standard issued to this edition.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American National Standards.The Consensus Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate.The proposed code or standard was made available for public re-view and comment which provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not approve,rate,or endorse:any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document,and does not undertake to insure any-one utilizing a standard against liability for infringement of any applicable Letters Patent,nor assume any such liability.Users of a code or standard are expressly advised that the determi-nation of the validity of any such patent rights,and the risk of infringement of such rights,is entirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations issued in accordance with gov-erning ASME procedures and policies which preclude the issuance of interpretations by indi-vidual volunteers.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical Engineers 345 E.47th Street New York,NY 10017 Copyright Q 1997 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All Rights Reserved Printed in USA.Copyright 1997 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.(This Foreword is not part of ASME Y14.35M-1997.)Subcommittee 35,Revision of Engineering Drawings,was formed in November 1981,as a subcommittee of ASME Standards Committee Y14,Engineering Drawing and Related Documentation Practices.The Subcommittee is charged