ASME_Y14-24-2012.pdf

Types and Applications of Engineering DrawingsEngineering Drawing and Related Documentation PracticesAN AM E R IC AN NAT IO NAL STANDARDASME Y14.24-2012Revision of ASME Y14.24-1999(R2009)Copyright ASME International Provided by IHS under license with ASME Licensee=University of Texas Revised Sub Account/5620001114 Not for Resale,06/26/2013 17:49:22 MDTNo reproduction or networking permitted without license from IHS-,-,-ASME Y14.24ADOPTION NOTICEASME Y14.24,“DRAWINGS TYPES AND APPLICATIONS OF ENGINEERING DRAWINGS”,was adopted on14 February 2000 for use by the Department of Defense(DoD).Proposed changes by DoD activities must besubmittedtotheDoDAdoptingActivity:Commander,U.S.ArmyARDEC,ATTN:RDAR-QES-E,PicatinnyArsenal,NJ 07806-5000.Copies of this document may be purchased from the American Society of Mechanical Engineers(ASME),Three Park Avenue New York,New York,United States,10016-5990.http:/www.asme.org/Custodians:Adopting Activity:Army ARArmy ARNavy SA(Project DRPR-2012-001)Air Force 16DLA DHReview Activities:Army AV,CR,MI,PT,TE,TMNavy AS,CG,CH,MC,NPAir Force 04,13,99DLA ISOSD SEOther CM,MP,DC2,NSNOTE:The activities listed above were interested in this document as of the date of this document.Sinceorganizations and responsibilities can change,you should verify the currency of the information above usingthe ASSIST Online database at 752839 http:/assist.dla.mil.AMSC N/AAREA DRPRDISTRIBUTION STATEMENT A.Approved for public release,distribution is unlimitedCopyright ASME International Provided by IHS under license with ASME Licensee=University of Texas Revised Sub Account/5620001114 Not for Resale,06/26/2013 17:49:22 MDTNo reproduction or networking permitted without license from IHS-,-,-ASME Y14.24-2012Revision of ASME Y14.24-1999(R2009)Types andApplications ofEngineeringDrawingsEngineering Drawing and RelatedDocumentation PracticesAN AMERICAN NATIONAL STANDARDTwo Park Avenue New York,NY 10016 USACopyright ASME International Provided by IHS under license with ASME Licensee=University of Texas Revised Sub Account/5620001114 Not for Resale,06/26/2013 17:49:22 MDTNo reproduction or networking permitted without license from IHS-,-,-Date of Issuance:April 5,2013This Standard will be revised when the Society approves the issuance of a new edition.There willbe no written interpretations of the requirements of this Standard issued to this edition.Periodically certain actions of the ASME Y14 Committee may be published as Cases.Cases arepublished on the ASME Web site under the Committee Pages at http:/cstools.asme.org/as they areissued.Errata to codes and standards may be posted on the ASME Web site under the Committee Pages toprovide corrections to incorrectly published items,or to correct typographical or grammatical errorsin codes and standards.Such errata shall be used on the date posted.The Committee Pages can be found at http:/cstools.asme.org/.There is an option available toautomatically receive an e-mail notification when errata are posted to a particular code or standard.ThisoptioncanbefoundontheappropriateCommitteePageafterselecting“Errata”inthe“PublicationInformation”section.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American NationalStandards.The Standards Committee that approved the code or standard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participate.The proposed code or standard was madeavailable forpublic review andcomment thatprovides an opportunityfor additional publicinput from industry,academia,regulatory agencies,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with anyitems mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability forinfringement of any applicable letters patent,nor assumes any such liability.Users of a code or standard are expresslyadvised that determination of the validity of any such patent rights,and the risk of infringement of such rights,isentirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted asgovernment or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the establishedASME procedures and policies,which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersTwo Park Avenue,New York,NY 10016-5990Copyright 2013 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted