ASME_NQA-1-Addn-b-2007.pdf

ASME NQA-1b2007Addenda toASME NQA-12004Quality Assurance Requirementsfor Nuclear Facility ApplicationsAN AMERICAN NATIONAL STANDARDThree Park Avenue New York,NY 10016A105EBCopyright 2007 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.Date of Issuance:June 1,2007ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American NationalStandards.The Standards Committee that approved the code or standard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participate.The proposed code or standard was madeavailableforpublicreviewandcommentthatprovidesanopportunityforadditionalpublicinputfromindustry,academia,regulatory agencies,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with anyitems mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability forinfringement of any applicable letters patent,nor assumes any such liability.Users of a code or standard are expresslyadvised that determination of the validity of any such patent rights,and the risk of infringement of such rights,isentirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted asgovernment or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the establishedASME procedures and policies,which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright 2007 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.Copyright 2007 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ASME NQA-1b2007Following approvalby theStandards Committee ofthe Committeeon Nuclear QualityAssurance,and after public review,ASME NQA-1b2007 was approved by the American National StandardsInstitute on April 5,2007.AddendatoASMENQA-12004areissuedintheformofreplacementpages.Revisions,additions,and deletions are incorporated directly into the affected pages.It is advisable,however,that thispage,the Addenda title and copyright pages,and all replaced pages be retained for reference.SUMMARY OF CHANGESThis is the second Addenda to be published to ASME NQA-12004.Replace or insert the pages listed.Changes given below are identified on the pages by a marginnote(b07),placed next to the affected area.Changes made in ASME NQA-12004 are indicatedby(04).Previous addenda changes are indicated by(a05).The pages not listed are the reversesides of the listed pages and contain no changes.PageLocationChange5,6Part I,Introduction(1)Definition of design input revised(2)Definition of quality standard added7Requirement 1,201(d)Revised810Requirement 2,201 and 301RevisedRequirement 2,305Added1113Requirement 3,300(a)Last sentence addedRequirement 3,501.3Second sentence addedRequirement 3,600(a)RevisedRequirement 3,700Revised16Requirement 5First sentence revised18Requirement 7,501Revised24Requirement 10(1)Paragraph 604 added(2)New para.700 added(3)Former para.700 redesignated aspara.80026Requirement 11,600Revised in its entirety30Requirement 15,405First sentence revised32,33Requirement 17Revised in its entirety34Requirement 18,303Last sentence added37ContentsUpdated to reflect addenda108112Subpart 2.21Moved to Part III and redesignated asNonmandatory Appendix 2.21114ContentsUpdated to reflect addenda116Nonmandatory AppendixRevised1A-1,303(c)Copyright 2007 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.PageLocationChange127129Nonmandatory Appendix(1)Paragraph 200(c)revised3A-1(2)New para.200(d)added,subsequentparagraphs redesignated(