ASME_PCC-1-2000.pdf

STD.ASME PCC-1-ENGL 20000759b700b20912127U08眼U脏BAB低JOINT ASSEMBLY。mitted without license from IHSlct forSTD.ASME PCC-1-ENGL 2000 0759670 0620913 063The American Society ofMechanical EngineersAN AM E RI C AN N AT I ON A L STA N D A R DGUIDELINES FORPRESSURE BOUNDARYBOLTED FLANG旺JOINT ASSEMBLYASME PCC-1-2000Not for ResaleSTD.ASME PCC-1-ENGL 2000 0759670 0620914 TTTDate of Issuance:February 28,2001There will be no addenda issued to this 2000 edition.The next edition of this Standardis scheduled for publication in 2003.ASME will issue written replies to inquiries concerning interpretations of technicalaspects of this Standard.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for AmericanNational Standards.The Standards Committee that approved the code or standard was balanced to assurethat individuals from competent and concerned interests have had an opportunity to participate.Theproposed code or standard was made available for public review and comment that provides an opportunityfor additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does notapprove,rate,orendorseany item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connectionwith any items mentioned in this document,and does not undertake to insure anyone utilizing a standardagainst liability for infringement of any applicable letters patent,nor assumes any such liability.Users ofa code or standard are expressly advised that determination of the validity of any such patent rights,andthe risk of infringement of such rights,is entirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to beinterpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordancewith the established ASME procedures and policies,which precludes the issuance of interpretations byindividuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright 2001 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll Rights ReservedPrinted in U.S.A.e wth ASMENo reproduction or networking permitted without license from IHSNot for ResaleSTD.ASME PCC-1-ENGL 2000 0759670 0620915 93bFOREWORDASME formed an Ad Hoc Task Group on Post Construction in 1993 in response toan increased need for recognized and generally accepted engineering standards forthe inspection and maintenance of pressure equipment after it has been placed inservice.At the recommendation of this Task Group,the Board on Pressure TechnologyCodes and Standards(BPTCS)formed the Post Construction Committee(PCC)in 1995.The scope of this committee was to develop and maintain standards addressing commonissues and technologies related to post-construction activities and to work with otherconsensus committees in the development of separate,product-specific codes andstandards addressing issues encountered after initial construction for equipment andpiping covered by Pressure Technology Codes and Standards.The BPTCS coversnon-nuclear boilers,pressure vessels(including heat exchangers),piping and pipingcomponents,pipelines,and storage tanks.The PCC selects standards to be developed based on identified needs and theavailability of volunteers.The PCC formed the Subcommittee on Inspection Planningand the Subcommittee on Flaw Evaluation in 1995.In 1998,a Task Group under thePCC began preparation of Guidelines for Pressure Boundary Bolted Flange Joint Assemblyand in 1999 the Subcommittee on Repair and Testing was formed.Other topics areunder consideration and may possibly be developed into future guideline documentsThe subcommittees were charged with preparing standards dealing with severalaspects of the in-service inspection and maintenance of pressure equipment and piping.The Inspection Planning Standard provides guidance on the preparation of a risk-basedinspection plan.Defects that are identified are then evaluated,when appropriate,usingthe procedures provided in the Flaw Evaluation Standard.Finally,if it is determinedthat repairs are required,guidance on repair procedures is provided in the appropriateRepair of Pressure Equipment and Piping Standard.These documents are in variousstages of preparation.None of these documents are Codes.They provide recognized and generally acceptedgood practices that may be used in conjunction with Post-Construction Codes,suchas API 510,API 570,and NB-23,and with jurisdictional requirements.The first edition of ASME PCC-1,Guidelines for Pressure Boundary Bolted FlangeJoint Assembly,was approved for publication in 2000.ASME PCC-1-2000 was approvedby ANSI as an American National Standard on November 15,2000.分Copyright ASME IntemationalNot for ResaleSTD.ASME PCC-1-ENGL200007596700620916872PERSONNELASME POST CONSTRUCTION COMMITTEESUBCOMMITTEES AND SUBGROUPSAs of November 15,2000Subgroup on Material PropertiesSTANDARDS COMMITTEED.W.Gandy.ChairW.F.Newell,Ir.J.R.Sims,Ir.ChairK.EnnisK.K.ColemanR.E.SmithC.Becht IV,Vice ChairW.J.KovesW.D.DotyE.UpitisJ.Labrador,SecretaryD.A.Lang.Sr.I.F.HenryS.D.YukawaG.A.AntakiC.R.LeonardW.H.Bamford Ir.D.A.Mauney1.E.BateyE.MichalopoulosD.L.BergerK.MokhtarianJ.M.BloomC.C.NeelySubgroup on Creep and Fatigue Crack GrowthG.BynogD.A.Osage)M.Bloom,ChairD.P.JonesP.N.ChakuF.OsweillerR.K.BezzantD.A.OsageC.D.CowferJ.T.ReynoldsI.D.FishburnM.SaiedfarD.W.GandyEXECUTIVE COMMITTEESUBCOMMITTEE ON INSPECTION PLANNINGC.Becht IV,ChairW.J.KovesD.A.Mauney,ChairD.A.Lang,Sr.I.R.Sims,Jr.Vice ChairD.A.MauneyD.L.Berger,Vice ChairI.Le MayI.Labrador,SecretaryK.MokhtarianP.A.Reddington,SecretaryC.R.LeonardG.A.AntakiJ.T.ReynoldsL.P.AntalffyL.F.MagerD.L.Berger)L.ArnoldE.MichalopoulosJ.E.BateyC.C.NeelyP.N.Chaku)T.ReynoldsC.D.CowferM.E.SchmidtSUBCOMMITTEE ON FLAW EVALUATIONF.R.Duvic IllJ.R.SimsK.EnnisH.N.Titer,Jr.W.J.Koves,ChairG.GaricK.Mokhtarian,Vice Chair C.P.HsiaoLabrador,SecretaryD.A.OsageC.Becht IVM.D.RanaSubgroup on Fully Quantitative1.M.BloomR.S.VecchioJ.D.FishburnR.K.YeeD.A.Mauney,ChairG.A.MontgomeryD.W.GandyS.D.YukawaP.A.Reddington,Secretary M.E.SchmidtH.N.Titer,Jr.A.TroyanovskyE.MichalopoulosSubgroup on FlawsD.A.Osage,ChairD.S.KimSubgroup on QualitativeC.P.Hsiao,Vice ChairW.C.LundineC.D.Cowfer,ChairN.Y.FaranssoT.A.BaconK.MokhtarianP.A.Reddington,Secretary B.KellerhallC.Becht IVH.MurakamiC.R.LeonardD.A.Lang.Sr.1.M.BloomM.D.RanaL.P.AntalffyL.F.MagerA.F.DeardorffW.G.ReuterJ.L.AmnoldC.C.NeelyJ.D.FishburnM.SaiedfarJ.E.BateyI.T.ReynoldsG.GaricD.R.ThorntonD.L.BergerC.D.RoderyP.GremaudR.S.VecchioP.N.ChakuD.A.WrightD.P.lonesR.K.YeeF.R.Duvic IllPrevious page is blank.wh ASMENo reproduction or networking permitted without license from IHSNot for Hesale