QA-1_Addn-a_2009.pdf

ASME NQA-1a2009Addenda toASME NQA-12008Quality Assurance Requirementsfor Nuclear Facility ApplicationsAN AMERICAN NATIONAL STANDARDThree Park Avenue New York,NY 10016A105A1Copyright 2009 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.Date of Issuance:August 31,2009ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American NationalStandards.The Standards Committee that approved the code or standard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participate.The proposed code or standard was madeavailable forpublic review andcomment thatprovides an opportunityfor additional publicinput from industry,academia,regulatory agencies,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with anyitems mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability forinfringement of any applicable letters patent,nor assumes any such liability.Users of a code or standard are expresslyadvised that determination of the validity of any such patent rights,and the risk of infringement of such rights,isentirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted asgovernment or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the establishedASME procedures and policies,which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright 2009 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.Copyright 2009 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ASME NQA-1a2009Following approval by the ASME NQA Committee and ASME,and after public review,ASMENQA-1a2009wasapprovedbytheAmericanNationalStandardsInstituteonJuly20,2009.Addenda to the 2008 edition of ASME NQA-1 are issued in the form of replacement pages.Revisions,additions,anddeletionsareincorporateddirectlyintotheaffectedpages.Itisadvisable,however,that this page,the Addenda title and copyright pages,and all replaced pages be retainedfor reference.SUMMARY OF CHANGESThis is the first Addenda to be published to ASME NQA-12008.Replace or insert the pages listed.Changes given below are identified on the pages by a marginnote,(a),placed next to the affected area.Revisions to the 2008 Edition are indicated by(08).The pages not listed are the reverse sides of the listed pages and contain no changes.PageLocationChangeivviForewordRevised46Part I,400Revised12Requirement 3,300Revised2022Requirement 7,700Revised in its entiretyRequirement 7,800Subparagraph(d)deleted26,27Requirement 11Revised in its entirety44Subpart 2.1,304.1Revised4649Subpart 2.1,400RevisedSubpart 2.1,600RevisedSubpart 2.1,801RevisedSubpart 2.1,802.2RevisedSubpart 2.1,802.3RevisedSubpart 2.1,900Revised5061Subpart 2.2Revised in its entirety7679.1Subpart 2.7,102(1)Definitions of acceptance testing andsoftware life cycle revised(2)Definition of regression testing addedSubpart 2.7,203(b)(3)RevisedSubpart 2.7,302RevisedSubpart 2.7,401RevisedSubpart 2.7,402RevisedSubpart 2.7,405RevisedSubpart 2.7,406(c)Revised(c)Copyright 2009 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.PageLocationChange8689.3Subpart 2.14Revised in its entirety138Nonmandatory AppendixDeleted11A-1143145Subpart 3.1,200Revised in its entirety148150.1Nonmandatory AppendixRevised18A-1,203.1153Nonmandatory Appendix(1)Subparagraphs(a)and(b)deleted2.1,300(2)Subparagraphs(c)and(d)deleted,redesignated as(a)and(b)154Nonmandatory AppendixRevised2.15,100179Subpart 4.1,404First par