分享
ASME_BTH-1-2005.pdf
下载文档

ID:167898

大小:11.37MB

页数:62页

格式:PDF

时间:2023-03-03

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
ASME_BTH 2005
ASME BTH-1-2005Design ofBelow-the-HookLifting DevicesAN AMERICAN NATIONAL STANDARDSThe American Society ofMechanical EngineersNot for ResaleASME BTH-1-2005Design ofBelow-the-HookLifting DevicesAN AMERICAN NATIONAL STANDARD拉。The American Society ofMechanical EngineersThree Park Avenue.New York,NY 10016。whAgNo roproduction or natworking permitled without liconso from IHSNot for ResaloCONTENTSForewordCommittee Roster.yCorrespondence With the BTH Committeet月tge,。t。t。t,书年。t。,。t。t。书月。年e年。t。t。t。eg。年。,。+viiChapter 1Scope and Definitions.11-1Purpose11-2Sc0p11-3New and Existing Devices11-4General Requirements.11-5Definitions31-6Symbols.51-7References8Chapter 2Lifter Classifications.112-1General112-2Design Category112-3Service Class12Chapter 3Structural Design.133-1General.133-2Member Design153-3Connection Design3-4Fatigue Design283-5Other Design Considerations29Chapter 4Mechanical Design404-1General.404-2Sheaves404-3Wire Rope414-4Drive Systems424-5Gearing434-6Bearings4-7Shafting44-8Fasteners47Chapter 5Electrical Components485-1General485-2Electric Motors and Brakes.45-3Limit Switches,Sensors,and Push Buttons5-4Controllers and Rectifiers for Lifting Device Motors.495-5Grounding5-6Power Disconnects55-7Batteries.51FiguresC3-1Selected Examples of Table 3-1 Requirements.C3-2Block Shear2C3-3Pin-Connected Plate Notation.C3-4Stiffened Plate Lifting Beam.24-1Sheave Dimensions4-2Sheave Gap¥进No roproduction or notworking permitled without liconso from IHSNot for ResaleTables2-1Service Class,4C2-1Service Class Life.C3-1Design Category A Static Load Spectrum.14C3-2Design Category A Dynamic Load Spectrum.C3-3Design Category B Static Load Spectrum.14C3-4Design Category B Dynamic Load Spectrum.143-1Limiting Width-Thickness Ratios for Compression Elements.163-2Minimum Effective Throat Thickness of Partial-Penetration Groove Welds.3-3Minimum Sizes of Fillet Welds.273-4Allowable Stress Ranges,ksi(MPa).23-5Fatigue Design Parameters.304-1Strength Factors for Calculating Load Capacity(American Standard ToothF0rms)434-2Lgg Life.4-3aKey Size Versus Shaft Diameter(ASME B17.1).4-3bKey Size Versus Shaft Diameter(DIN 6885-1).454-4Fatigue Stress Amplification Factors.4No roproduction or notworking permitled without liconso from IHSNot for Resalo

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开