BPVC_2021_Section_XII.pdf

ASME BPVC.XII-2021Rules for Constructionand Continued Serviceof Transport TanksSECTION XII2021ASME Boiler andPressure Vessel CodeAn International CodeMarkings such as“ASME,”“ASME Standard,”or any other marking including“ASME,”ASME logos,or the ASME Single Cerficaon Mark shall not be used on any item that is not constructed in accordance with all of the applicable requirements of the Code or Standard.Use of of the ASME Single Cerficaon Mark requires formal ASME cerficaon;if no cerficaon program is available,such ASME markings may not be used.(For Cerficaon and Accreditaon Programs,see hps:/www.asme.org/cerficaon-accreditaon.)Items produced by pares not formally possessing an ASME Cerficate may not be described,either explicitly or implicitly,as ASME cerfied or approved in any code forms or other document.XIIRULES FOR CONSTRUCTIONAND CONTINUED SERVICE OFTRANSPORT TANKSASME Boiler and Pressure Vessel Committeeon Transport TanksAN INTERNATIONAL CODE2021 ASME Boiler&Pressure Vessel Code2021 EditionJuly 1,2021Two Park Avenue New York,NY 10016 USADate of Issuance:July 1,2021This international code or standard was developed under procedures accredited as meeting the criteria forAmerican National Standards and it is an American National Standard.The Standards Committee that approvedthe code or standard was balanced to assure that individuals from competent and concerned interests havehad an opportunity to participate.The proposed code or standard was made available for public review and com-ment that provides an opportunity for additional public input from industry,academia,regulatory agencies,andthe public-at-large.ASME does not“approve,certify,“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with anyitems mentioned in this document,and does not undertake to insure anyone utilizing a standard against liabilityfor infringement of any applicable letters patent,nor assume any such liability.Users of a code or standard areexpressly advised that determination of the validity of any such patent rights,and the risk of infringement of suchrights,is entirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted asgovernment or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the es-tablished ASME procedures and policies,which precludes the issuance of interpretations by individuals.The endnotes and preamble in this document(if any)are part of this American National Standard.ASME Collective Membership MarkASME Single Certification MarkASME and the above ASME symbols are registered trademarks of The American Society of Mechanical Engineers.No part of this document may be reproduced in any form,in an electronicretrieval system or otherwise,without the prior written permission of thepublisher.Library of Congress Catalog Card Number:56-3934Printed in the United States of AmericaAdopted by the Council of The American Society of Mechanical Engineers,1914;latest edition 2021.The American Society of Mechanical EngineersTwo Park Avenue,New York,NY 10016-5990Copyright 2021 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedTABLE OF CONTENTSList of Sections.xviForeword.xviiiStatement of Policy on the Use of the ASME Single Certification Mark and Code Authorization in AdvertisingxxStatement of Policy on the Use of ASME Marking to Identify Manufactured Items.xxSubmittal of Technical Inquiries to the Boiler and Pressure Vessel Standards Committees.xxiPersonnel.xxivSummary of Changes.xlvList of Changes in Record Number Order.xlviiiCross-Referencing and Stylistic Changes in the Boiler and Pressure Vessel Code.xlixPart TGGeneral Requirements.1Article TG-1Scope and Jurisdiction.1TG-100Introduction.1TG-110Scope.1TG-120Vessel Classifications.2TG-130Documents Referenced by This Section.2TG-140Units of Measurement.4TG-150Equations.4TG-160Tolerances.4Article TG-2Organization of Section XII.5TG-200Parts.5TG-210Appendices.5TG-220Articles and Paragraphs.5TG-230References.5TG-240Terms and Definitions.5Article TG-3Responsibilities and Duties.6TG-300General.6TG-310Owners Responsibility.6TG-320Manufacturers Responsibility.6TG-330Inspectors Duties.7Article TG-4General Rules for Inspection.8TG-400General Requirements for Inspection and Examination.8TG-410The Inspector.8TG-420Access for the Inspector.8TG-430The Manufacturer.9TG-440Continued Service.9Part TMMaterial Requirements.10Article TM-1Material Requirements.10TM-100General.10TM-110General Requirements for All Products.10TM-120Material Identified With or Produced to aSpecification Not Permitted by ThisSection,and Material Not Fully Identified.13TM-130Material Specifications.15TM-140Inspection and Marking of Materials.15TM-150Additional Requirements for Carbon and Low Alloy Steels.32TM-1