ASME_B94
45
1979
A M E R I C A N N A T I O N A L S T A N D A R D Precision Holders for Indexable Inserts ANSI B94.45M-1979(REVISION OF 694.45-1973 AND BW.45a-1975)SECRETA RIA 7 THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLISHED BY T H E A M E R I C A N S O C I E T Y O F M E C H A N I C A L E N G I N E E R S United Engineering Center New York,N.Y.1 O01 7 3 4 5 East 47th Street Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:49:59 MSTNo reproduction or networking permitted without license from IHS-,-,-9009275 OOZY350 913 Date of Issuance:March 31,1980 No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.Copyright O 1980 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS Printed in U.S.A.Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:49:59 MSTNo reproduction or networking permitted without license from IHS-,-,-9009275 00243511 5T FOREWORD The material contained in this Standard was developed by Technical Committee I,Carbide and Oxide Tools of American National Standards Committee B94,Cutting Tools,Holders,Drivers,and Bushings,after a thorough investigation of all factors involved.It is based on sound Engineering practice and reflects the requirements of the industry.This Standard incorporates the subject matter contained in its predecessor ANSI B94.45-1973,Precision Indexable Insert Holders,and also ANSI B94.45a,Insert Radius Compensation Charts for Precision Index-able Insert Holders,which was a partial revision of B94.45-1973.It replaces both of those Standards.The title has been changed to more accurately describe the contents.The Standard was submitted to American National Standards Committee B94 Cutting Tools,Holders,Drivers,and Bushings and was approved by letter ballot on March 29,1979.The Secretariat,The American Society of Mechanical Engineers approved the Standard on September 14,1979.The Standard was approved by American National Standards Institute on October 30,1979,and designated ANSI B94.45M-1979.iii Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:49:59 MSTNo reproduction or networking permitted without license from IHS-,-,-=7007275 0024352 796 AMERICAN NATIONAL STANDARDS COMMITTEE 694 Cutting Tools,Holders,Drivers and Bushings OFFICERS Harry McLinden,Chairman A.M.Metev.Vice-Chairman R.K.Buckley,Secretary AMERICAN GEAR MANUFACTURERS,ASSOCIATIONS THE P.M.Dean,Jr.,Mechanical Technology,Incorporated,Latham,New York Robert C.Brown,Alternate,American Gear Manufacturers Association,Arlington,Virginia M.E.Merchant,Dr.,Cincinnati Milacron,Incorporated,Cincinnati,Ohio G.M.Monacelli,General Electric Company,Detroit,Michigan C.J.Oxford,Jr.,National Twist Dra&Tool Company,Rochester,Michigan AMERICAN SOCIETY OF MECHANICAL ENGINEERS,THE CEMENTED CARBIDE PRODUCERS ASSOCIATION J.A.Woodward,Teledyne Firth Sterling,Pittsburgh,Pennsylvania A.?Wherry,Alternate,Cemented Carbide Products Association,Cleveland,Ohio CUTTING TOOL MANUFACTURERS ASSOCIATION.J.Czopor,Falcon Tool Company,Warren,Michigan C.W.Jatho,Alternate,Cutting Tool Manufacturers Association,Birmingham,Michigan GENERAL SERVICES ADMINISTRATION W.R.Wacker,Federal Supply Service(FMET),Washington,D.C.William 5.Korb,The Henry G.Thompson Company,Branford,Connecticut C.M.Stockinger,Alternate,Hack&Band Saw Manufacturers Association of America,Cleveland,HACK&BAND SAW MANUFACTURERS ASSOCIATION OF AMERICA Ohio METAL CUTTING TOOL INSTITUTE W.A.Wagner,Cleveland Twist DriU Company,Cleveland,Ohio F.A.Petersen,Metal Cutting Tool Institute,Cleveland,Ohio MOTOR VEHICLE MANUFACTURERS ASSOCIATION A.Neinast,Corporate Standards International Harvester,Hinsdale,Illinois 8.Ross Ashby,Alternate,Motor Vehicle Manufacturers Association of the United States,Incorporated,Detroit,Michigan NATIONAL ASSOCIATION OF PUNCH MANUFACTURERS Richard Thomas,Dayton Progress Corporation,Dayton,Ohio NATIONAL BUREAU OF STANDARDS J.R.Pidgeon.National Bureau of Standards,Washington,D.C.NATIONAL MACHINE TOOL BUILDERS ASSOCIATION G.F.Wilson,General Electric Company,Worthington,Ohio John 8.Deam,Alternate,National Machine Tool Builders Association,McLean,Virginia C.H.Lang,Society of Carbide Engineers,Bridgeville,Pennsylvania K.A.L undell,The Producto Machine Company,Jamestown,New York Harry McLinden,Caterpillar Tractor Company,Peoria,Illinois W.N.Moore,The Ford Motor Company,Dearbom,Michigan SOCIETY OF CARBIDE ENGINEERS SOCIETY OF MANUFACTURING ENGINEERS TELEPHONE GROUP R.A.Agnew,Western Electric Company,Incorporated,Chicago,Illinois S.P.Rogacki,Alternate,Western Electric Company Incorporated,Kearny,New Jersey V Copyright ASME International Provided by IHS under license with ASME Licensee