_BPE_Addn-a_2004.pdf

AN AMERICAN NATIONAL STANDARDASME BPE-a2004ADDENDAtoASME BPE-2002BIOPROCESSING EQUIPMENTTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSThree Park Avenue O New York,NY 10016Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.Date of Issuance:May 20,2005ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria forAmerican National Standards.The Standards Committee that approved the code or standardwas balanced to assure that individuals from competent and concerned interests have had anopportunity to participate.The proposed code or standard was made available for public reviewand comment that provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted inconnection withany itemsmentioned inthis document,and doesnot undertaketo insureanyoneutilizing a standardagainst liability for infringementof any applicable letterspatent,nor assumesany such liability.Users of a code or standard are expressly advised that determination of thevalidity of any such patent rights,and the risk of infringement of such rights,is entirely theirown responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not tobe interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued inaccordance with the established ASME procedures and policies,which precludes the issuanceof interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright 2005 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ASME BPE-a2004SUMMARY OF CHANGESFollowing approval by the ASME BPE Committee and ASME,and after public review,ASME BPE-a2004 was approved by the American National Standards Institute on June 7,2004.Addenda to BPE-2002 are issued in the form of replacement pages.Revisions,additions,and deletions areincorporated directly into the affected pages.It is advisable,however,that this page,the Addenda title andcopyright pages,and all replaced pages be retained for reference.SUMMARY OF CHANGESThis is the first addenda to be published to ASME BPE-2002.Replace or insert the pages listed.Changes given below are identified on the pages by a margin note(a)placed next to the affected area.The pages not listed are the reverse sides of the listed pages and containno changes.PageLocationChangeiii viContentsUpdated to reflect 2004 addendaxiiCommittee rosterUpdated to reflect 2004 addenda1GR-1First para.revisedGR-2First para.revised3,4,4.1,6,7GR-9(1)ASTM A 967 added(2)ASTM B 912 addedGR-10(1)Definitions of blind weld;cluster of pits;electropolishing;personal care products;pharmaceutical;pickling;Ramax.;andseal point added14SD-3.11.1(1)First para.revised(2)Third para.added15Table SD-1(1)Sketch revised(2)Third and sixth columns deleted(3)Current fourth and fifth columns revised16Table SD-2Deleted17Table SD-3Deleted18Table SD-4Deleted19Table SD-5(1)Sketch revised(2)Fifth and eighth columns deleted(3)Current sixth and seventh columns revised20Table SD-6(1)Fifth and eighth columns deleted(c)Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.PageLocationChange(2)Sixth and seventh columns revised21Figure SD-3Sketches(c)and(e)revised23,24SD-4.5.1(c)RevisedFigure SD-6Revised25SD-4.7.1Subparagraph(e)revised26Figure SD-8Revised in its entirety27Figure SD-9Revised in its entirety28Figure SD-11(1)Title revised(2)Revised in its entirety29SD-4.7.5Subparagraph(c)revised31Figure SD-15Title revised33Figure SD-17Sketches(f)and(g)revised37Figure SD-22Title revisedSD-4.9.2RevisedSD-4.9.3Subparagraph(a)revised41SD-5.1Corrected by errataSD-6Subparagraph(p)added43 45DT-1First paragraph revisedDT-2First paragraph revisedDT-3.1Subparagraph(a)revisedDT-3.4(1)First and second paragraphs revised(2)Third paragraph addedDT-3.5Second para.editorially revisedTable DT-2General note revisedTable DT-3Sixth and seventh entries in second columnrevisedDT-6(1)Second pa