ASME_B94.25-1982.pdf

9007275 0024273 53T INDE ERRATA to ANSI 894.25-1982 ABLE INSERTS FOR CUTTI.S TOOLS Page 21,Table 11-Under the Insert Designation col-umn,correct SPG to read SPGR throughout the column THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS 345 East 47th Street,New York,NY 10017 June 1983 Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:49:18 MSTNo reproduction or networking permitted without license from IHS-,-,-A M E R I C A N N A.T I O N A L S T A N D A R D Indexable Inserts for Cutting Tools ANSI B94.25-1982(REVISION OF ANSI 894.25-1975)SECRETARIA T THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLISHED BY T H E A M E R I C A N S O C I E T Y OF M E C H A N I C A L E N G I N E E R S United Engineering Center New York,N.Y.1 O 0 1 7 345 East 47th Street Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:49:18 MSTNo reproduction or networking permitted without license from IHS-,-,-ASME B74.25 82=2595512 0017789 T Date of Issuance:August 31,1982 This code or standard was developed under procedures accredited as meeting the criteria for American National Standards.The Consensus Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate.The proposed code or standard was made available for public review and comment which provides an opportunity for additional public input from industry,academia,regulatory agen-cies,and the public-at-large.ASME does not approve,rate,or endorse any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable Letters Patent,nor assume any such liability.Users of a code or standard are expressly advised that determination of the validity of any such patent rights,and the risk of infringement of such rights,is entirely their own responsibility.Participation by federal agency representativek)or person(sl affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.Copyright O 1982 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All Rights Reserved Printed in U.S.A.Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:49:18 MSTNo reproduction or networking permitted without license from IHS-,-,-ASME B4Lt.25 82 2575532 0037790 b W FOREWORD The material contained in this Standard was developed by Technical Committee 1,Carbide and Oxide Tools of USA Standards Committee B94,Cutting Tools,Holders,Drivers,and Bushings,after a thorough investigation of ali factors involved.It is based on sound engineering practice and reflects the requirements of the industry.The Standard was submitted to USA Standards Committee B94,Cutting Tools,Holders,Drivers,and Bushings on December 28,1968 and was approved by letter ballot on March 25,1969.The sponsor,The American Society of Mechanical Engineers,approved the Standard on July 25,1969.The Standard was approved by USA Standards Institute on September 10,1969 and designated USAS B94.25-1969.The current edition was approved as an American National Standard on March 5,1982.Nofe:Companion IS0 standard documents are IS0 883 and ISO/DiS 3364.2 iii Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:49:18 MSTNo reproduction or networking permitted without license from IHS-,-,-.ASME 894-25 A2 W 2575532 0017993 m AMERICAN NATIONAL STANDARDS COMMITTEE B94 CUTTING TOOLS,HOLDERS,DRIVERS AND BUSHINGS OF FI CERS A.R.Neinast,Chairman A.M.Mezey,Vice-Chairman W.R.Daisak,Secretary AMERICAN SOCIETY OF MECHANICAL ENGINEERS,THE A.Neinast,International Harvester Company,Hinsdale,Illinois M.E.Merchant,Cincinnati Milacron,Incorporated,Cincinnafi,Ohio C.J.Oxford,NationalTwist Drill&Tool Conipany,Rochester,Michigan C.F.Wilson,Alternate,General Electric Company,Worthington,Ohio CEMENTED CARBIDE PRODUCERS ASSOCIATION A.P.Wherry,Alternate,Cemented Carbide Products Association,Cleveland,Ohio CUTTING TOOL MANUFACTURERS ASSOCIATION E.J.Czopor,Falcon Tool Company,Warren,Michigan C.W.Jatho,Alternate,Cutting Tool Manufacturers Association,Birmingliam,hlichigan GENERAL SERVICES ADMINISTRATION W.Wacker,Federal Supply Service,Washington,D.C.HACK AND BAND SAW MANUFACTURERS ASSOCIATION OP AMERICA.D.Schrade,Clemson Brothers,Incorpo