ASME_B94
46
1973
9009275 0024445 437 A M E R I C A N N A T I O N A L S T A N D A R D Carbide Seats Used with Indexable Inserts for Clamp Type Holders ANSI B94.46-1973 SECRETARIAT THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLISHED BY T H E -A M E R I C A N S O C I E T Y O F M E C H A N I C A L E N G I N E E R S United Engineering Center 345 East 47th Street New York,N.Y.1001 7 Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:50:00 MSTNo reproduction or networking permitted without license from IHS-,-,-9009275 002444b 373 Mo part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.Copyright O,1973,by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS Printed i n U.S.A.Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:50:00 MSTNo reproduction or networking permitted without license from IHS-,-,-t iii m 9009275 0024447 20T m FOREWORD The material contained in this standard was developed by Technical Committee 1,Carbideand Oxide Tools of American National Standards Committee B94,Cutting Tools,Holders,Drivers and Bushings,after a thorough investigation o f all factors involved.It is based on sound engineering practice and reflects the requirements of the industry and the users.This standard was approved as an American National Standard on October 10,1973.Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:50:00 MSTNo reproduction or networking permitted without license from IHS-,-,-9009275 0024448 146 AMERICAN NATIONAL STANDARDS COMMITTEE B94 CUTTING TOOLS,HOLDERS,DRIVERS AND BUSHINGS(The following is the roster of the Committee at the time of approval of this standard)OFFICERS H.J.Moffat,Chairman A.M.Mezey,Vice-chairman Harry McLinden,Secretary STAN DAR DS COMM I TT E E AMERICAN GEAR MANUFACTURERS ASSOCIATION,THE P.M.Dean,Jr.,Mechanical Technology,Inc.,Latham,New York G.L.Scott(Alt.),American Gear Manufacturers Assoc.,Washington,D.C.C.J.Oxford,Jr.,National Twist Drill&Tool Company,Rochester,Michigan M.Merchant,Or.,Cincinnati Milacron,Inc.,Cincinnati,Ohio G.M.Monacelli,General Electric Company,Detroit,Michigan AMERICAN SOCIETY OF MECHANICAL ENGINEERS,THE SOCIETY OF MANUFACTURING ENGINEERS H.J.Moffatf,Caterpillar Tractor Company,East Peoria,Illinois K.A.Lude/,The Producto Machine Company,Jamestown,New York W.E.Montgomery,Firth Sterling,Inc.,McKeesport,Pennsylvania A.P.Wherry,Cemented Carbide Producers Association,Cleveland,Ohio W.C.Petrie,Federal Supply Service,Washington,D.C.L.P.Sohies,Morse Twist Drill and Machine Co.,New Bedford,Massachusetts P.L.Houser,(Ait.)Metal Cutting Tool Institute,New York,New York NATIONAL ASSOCIATION OF PUNCH MANUFACTURERS R.J.Gargrave,Dayton Progress Corporation,Dayton,Ohio J.R.Pigeon,National Bureau of Standards,Washington,D.C W.H.Seacor,International Harvester Co.,Hinsdale,Illinois A.J.McLaren,The Cross Company,Fraser,Michigan C.H.Lang,c/o Society of Carbide Engineers,Milford,Connecticut M.C.Berryman,Western Electric Company,Inc.,Chicago,Illinois S.P.Rogacki(Alt.),Western Electric Company,Inc.,Kearney,New Jersey J.O.Snyder,Department of Air Force,Wright-Patterson AFB,Ohio R.K.Freeman,U.S.Department of Army,Rock Island,Illinois J.N.Segura(Alt.),U.S.Department of Army,Rock Island,Illinois CEMENTED CARBIDE PRODUCERS ASSOCIATION GENERAL SERVICES ADMINISTRATION METAL CUTTING TOOL INSTITUTE NATIONAL BUREAU OF STANDARDS SOCIETY OF AUTOMOTIVE ENGINEERS SOCIETY OF CARBIDE ENGINEERS TELEPHONE GROUP U.S.DEPARTMENT OF THE AIR FORCE U.S.DEPARTMENT OF ARMY iv.a-.Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:50:00 MSTNo reproduction or networking permitted without license from IHS-,-,-9009275 0024449 O82 U.S.DEPARTMENT OF THE NAVY N.N.Cornette,Naval Ship Systems Command,Washington,D.c.D.G.Jones,Kenametal,Inc.,Latrobe,Pennsylvania William Hofbauer,Mohawk Tools,Inc.,Montpelier,Ohio K.8.Kaiser,The Ingersoll Milling Machine Co.,Rockford,Illinois A.M.Mezey,Richards Brothers Punch Company,Detroit,Michigan W A.Wagner,The Cleveland Twist Drill Company,Cleveland,Ohio INDIVIDUAL COMPANIES INDIVIDUAL MEMBERS Anderson Ashburn,American Machinist,New York,New York F.P.Brown,Engineer,Vienna,Virginia B94 TECHNICAL COMMITTEE I CARBIDE AND OXIDE TOOLS J.W.Addler,Chairman,Caterpillar Tractor Company,East Peoria,Illinois A.P.Wherry,Secretary,Cemented Carbide Producers Association,Cleveland,Ohio J,A.Agnew,Adamas Carbide Corporation,Kenilworth,New Jersey J,W.Mendenhall,Bullard Company,Bridgeport,Connecticut W.E.Montgomery,A Teledyne Company,McKeesport,Pennsylvania Henry W Stier,Howmet Corporation,Plymouth,Mi