ASME_B94
47
1980
9009275 0024465 225 A M E R I C A N N A T I O N A L S T A N D A R D Carbide Chip Breakers Used with Indexable Inserts for Clamp Type Holders ANSI B94.47M-1980(REVISION OF 894.47-1973)SECRETARIAT THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLISHED BY T H E A M E R I C A N S O C I E T Y O F M E C H A N I C A L E N G I N E E R S United Engineering Center New York,N.Y.1 O01 7 345 East 47th Street Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:50:01 MSTNo reproduction or networking permitted without license from IHS-,-,-9009275 0024466 Lbl Date of Issuance:April 30,1981 No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the pub isher.Copyright O 1981 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All Rights Reserved Printed in U.S.A.Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:50:01 MSTNo reproduction or networking permitted without license from IHS-,-,-9009275 O024467 OTB=FOREWORD The material contained in this standard w a s developed by Technical Committee 1,Carbide and Oxide Tools of American National Standards Committee B94,Cutting Tools,Holders,Drivers and Bushings,after a thorough investigation of a l l factors involved.It is based on sound engineering practice and reflects the requirements of the industry and the users.This standard w a s approved as an American National Standard on October 27,1980.iii Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:50:01 MSTNo reproduction or networking permitted without license from IHS-,-,-9009275 00244b8 T34 9 AMERICAN NATIONAL STANDARDS COMMITTEE B94 CUTTING TOOLS,HOLDERS,DRIVERS AND BUSHINGS OF FI CERS A.R.Neinast,Chairman A.M.Merey.Vice-chairman R.K.Buckley,Secretary AMERICAN GEAR MANUFACTURERS,ASSOCIATIONS THE P.M.Dean,Jr.,Mechanical Technology,Inc.Latham,New York R.C.Brown,Alternate,Manager of Engineering Services,Arlington,Virginia M.E.Merchant,Or.,Cmdnati Milacron,Inc.,Cincinnati,Ohio C.J.Oxford,Jr.,National Twist Drill&Tool Co.,Rochester,Michigan G.F.Wilson,Alternete,General Electrical Co.,Worthington,Ohio A.P.Wherry,Cemented Carbide Products Association,Cleveland,Ohio E.J.Czopor,Falcon Tool Company,Warren,Michigan C W.Jarho,Alternate,Cutting Tool Manufacturers Association,Birmingham,Michigan W.R.Wacker,Federal Supply Service(FMET),Washington,D.C.HACK&BAND SAW MANUFACTURERS ASSOCIATION OF AMERICA W.B.Korb,The Henry G.Thompson Company,Branford,Connecticut C.M.Stockinger,Alternate,Hack&Band Saw Manufacturers Association of America,Cleveland,Ohio W.A.Wagner,Cleveland Twist Drill Company,Cleveland,Ohio F.A.Petersen,Metal Cutting Tool Institute,Cleveland,Ohio A.R.Neinast,Corporate Standards International Harvester,Hinsdale,Illinois B.R.Ashby,AlteJnte,Motor Vehicle Manufacturers Association of the United States,Inc.,Detroit,Michigan NATIONAL ASSOCIATION OF PUNCH MANUFACTURERS Richard Thomas,Dayton Progress Corp.,Dayton,Ohio G.i.Wilson,General Electric Company,Worhington,Ohio J.8.Deam,Alternate,National Machine Tool Builders Association,McLean,Virginia C.H.Lang,Society of Carbide Engineers,Bridgeville,Pennyslvda K.A.Lundell,The Producto Machine Company,Jamestown,New York Many McLinden,Caterpillar Tractor Company,Peoria,Illinois W.M.Moore,The Ford Motor Company,Dearbom,Michigan R.A.Agnew,Western Electric Co.,Inc.Chicago,Illinois S.P.Rogacki,Alternate,Western Electric Company Inc.,Keamy,New Jersey AMERICAN SOCIETY OF MECHANICAL ENGINEERS,THE CEMENTED CARBIDE PRODUCERS ASSOCIATION CUTTING TOOL MANUFACTURERS ASSOCIATION GENERAL SERVICES ADMINISTRATION METAL CUTTING TOOL INSTITUTE MOTOR VEHICLE MANUFACTURERS ASSOCIATION NATIONAL MACHINE TOOL BUILDERS ASSOCIATION SOCIETY OF CARBIDE ENGINEERS SOCIETY OF MANUFACTURING ENGINEERS TELEPHONE GROUP Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:50:01 MSTNo reproduction or networking permitted without license from IHS-,-,-m 7009275 0024469 970 m TUBULAR RIVET AND MACHINE INSTITUTE Steven Rooney,Alternate,Hi-Pro Tool Company,New Bedford,Massachusetts D.L.York,Liaison,U.S.Army Armament,Rock Isand,Illinois U.S.DEPARTMENT OF THE ARMY U.S.DEPARTMENT OF THE NAVY J.R.Ruff,Naval Ship Systems Command(SEA 605).,Washington,D.C.Haro/d Cooper,AES Certification Institute,Troy,Michigan Kenneth Hull,The Ingersoll Milling Machine Company,Rockford,Illinois A.M.Mezey,Richards Broa Punch Company,Detroit,Michigan Lyle Storrer,Mohawk Tools,Inc.,Montpelier,Ohio Anderson Ashburn,McGraw Hill,New York,New York INDIVIDUAL COMPANIES TECHNICAL COMMITTEE 1 CARBIDE AND OXIDE TOOLS C.C.Tobin,Chairman,Caterpillar Tractor Co.