ASME_B94.42-1972.pdf

9009275 0024340 T 4 A M E R I C A N N A T I O N A L S T A N D A R D Carbide Blanks for Tipping Circular Saws ANSI B94.42-1972(REVISION AND REDESIGNATION OF B108.1-1966)SECRETARIAT THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLISHED BY T H E A M E R I C A N S O C I E T Y O F M E C H A N I C A L E N G I N E E R S United Engineering Center New York,N.Y.1 O0 17 345 East 47th Street Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:49:59 MSTNo reproduction or networking permitted without license from IHS-,-,-9007275 0024341 9OOm No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.Copyright,0,1973 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS Printed in USA Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:49:59 MSTNo reproduction or networking permitted without license from IHS-,-,-9009275 0024342 847 F O R E W O R D The material contained in this document has been developed under the auspices of the Standards Committee of the Cemented Carbide Producers.Association.The dimensional listings together with the tolerances and nomenclature have been developed after a thorough investigation of all factors involved in the field of carbide blanks for circular saws.The original draft was prepared in February of 1962 and distributed to manu-facturers of the item for comment.Suggestions for revision were received and incorporated in subsequent drafts,and the material was finally approved by the CCPA Standards Committee in March of 1963.The material appearing in this standard is based on sound engineering practice and reflects the requirements of the industry.It was submitted to the American Standards Association,now the American National Standards Institute,for promul-gation as an American Standard in May of 1963.Technical Committee No.1 of American National Standards Committee B94,Cutting Tools,Holders,Drivers and Bushings recommended revision of the docu-ment in 1971.The standard was approved by the B94 Standards Committee and the American National Standards Institute on August 8,1972 and Redesignated B94.42-1972.I I I Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:49:59 MSTNo reproduction or networking permitted without license from IHS-,-,-9009275 0024343 783 AMER KAN NATIONAL STANDARDS COMMITTEE 894 CUTTING TOOLS,HOLDERS,DRIVERS AND BUSHINGS(The following i s the roster of the committee at the time of approval of this standard.)OFFICERS Harry J.Moffaii,Chairman A.M.Mezey,Vice-Chairman Harry McLinden,Secretary STANDARDS COMMITTEE AMERICAN GEAR MANUFACTURERS ASSOCIATION,THE p.M.Dean,Jr.,Mechanical Technology,Inc.,Latham,New York 12110 G.L.Scott(Alt.),American Gear Manufacturers Assoc.,Washington,D.C.20005 AMERICAN SOCIETY OF MECHANICAL ENGINEERS,THE c.J.Oxford,Jr.,National Twist Drill 86 Tool Company,Rochester,Michigan 48603 M.E.Merchant,Dr.,Cincinnati Milacron,Inc.,Cincinnati,Ohio 45209 G.M.Monacelli,General Electric Company,Detroit,Michigan 48232 SOCIETY OF MANUFACTURING ENGINEERS Harry J.Moffati,Caterpillar Tractor Company,East Peoria,Illinois 61611 Kermit A.Lundell,The Producto Machine Company,Jamestown,New York 14701 CEMENTED CARBIDE PRODUCERS ASSOCIATION W.E.Montgomery,Firth Sterling,Inc.,McKeesport,Pennsylvania Allen P.Wherry,Cemented Carbide Producers ASSOC.,Cleveland,Ohio 44115 w.c.f etrie,Federal Supply Service,Washington,D.C.20407 LeRoy P.Sohles,Morse Twist Drill and Machine Co.,New Bedford,Massachusetts 02740 Perry L.Houser(Alt.).Metal Cutting Tool Institute,New York,New York 10017 GENERAL SERVICES ADMINISTRATION METAL CUTTING TOOL INSTITUTE NATIONAL ASSOCIATION OF PUNCH MANUFACTURERS R.J.Gargrave,Dayton Progress Corporation.Dayton,Ohio 45449 NATIONAL BUREAU OF STANDARDS J.R.Pidgeon,National Bureau of Standards,Washington,D.C.20234 SOCIETY O F AUTOMOTIVE ENGINEERS W.H.Seacord,International Harvester Co.,Hinsdale,Illinois 60521 A.J.McLaren,The Cross Company,Fraser,Michigan 48026 SOCIETY OF CARBIDE ENGINEERS Charles H.Lang,c/o Society of Carbide Engineers,Milford,Connecticut 06460 TELEPHONE GROUP M.c.Berryman,Western Electric Company,Inc.,Chicago,Illinois 60623 5.f.Rogocki(Alt.),Western Electric Company,Inc.,Kearney,New Jersey 07032 U.S.DEPARTMENT O F THE AIR FORCE J.O.Snyder,Department of Air Force,Wright-Patterson AFB,Ohio 45433 U.S.DEPARTMENT O F ARMY Ralph K.Freeman,U.S.Department of Army,Rock Island,Illinois 61623 J.N.Segura(Alt.),U.S.Department of Army,Rock Island,Illinois 61201 U.S.DEPARTMENT OF THE NAVY N.N.Cornette,Naval Ship Systems Command,Washington,D.C.20360 V Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/59668