4-53_R1984_E1978.pdf

A M E R I C A N N A T I O N A L S T A N D.A R D Solid Steel Rectangular Metal Cutting Squaring Shear Knives Dimensional Tolerances SECRE TARlA T THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLISHED BY T H E A M E R I C A N S O C I E T Y O F M E C H A N I C A L E N G I N E E R S United Engineering Center 345 E a s t 47th Street New York,N.Y.1001 7 Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS Copyright 0 1978 by All Rights Reserved Printed in U.S.A.Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.FOREWORD The Metal Cutting Knife Association appointed the“Standards Committee”of the Association to re-view the possibility of standardizing“Squaring Shear Knives.”After reviewing this program the committee notified the members of Technical Committee#I 7 about this proposed standard and meetings were held on October 8,1974,April 8,1975,October 7,1975,March 9,1976,September 21,1976,December 7,1976 and March 22,1977.On May 6,1977 this Standardization Program was forwarded to the Chairman of the B94 Standards Committee,Technical Committee 17 for review and with anticipation of having it adopted as an American National Standard.This Standard was approved as an American National Standard on April 5,1978.iii Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.AMERICAN NATIONAL STANDARDS COMMITTEE I394 Standardization of Cutting Tools,Holders,Drivers and Bushings OFFICERS Harry McLinden,Chairman A.M.Metey,Vice-chairman Richard K.Buckley,Secrerary AMERICAN GEAR MANUFACTURERS ASSOCIATION,THE P.M.Dean,Jr.,Mechanical Technology,Inc.,Latham,New York G.L.Scott,Alternate,American Gear Manufacturers Association,Washington,D.C.AMERICAN SOCIETY OF MECHANICAL ENGINEERS,THE M.E.Merchant,Dr.,Cincinnati Milacron,Inc.,Cincinnati,Ohio G.M.Monacelli,General Electric Company,Detroit,Michigan C.J.Oxford,Jr.,National Twist DriII&Tool Company,Rochester,Michigan CEMENTED CARBIDE PRODUCERS ASSOCIATION J.A.Woodward,Teledyne Firth Sterling,Pittsburgh,Pennsylvania A.P.Wherry,Alternate,Cemented Carbide Producers Association,Cleveland,Ohio CUTTING TOOL MANUFACTURERS ASSOCIATION E.J.Czopor,Falcon Tool Company,Detroit,Michigan C.W.Jatho,Alternate,Cutting Tool Manufacturers Association,Birmingham,Michigan GENERAL SERVICES ADMINISTRATION W.R.Wacker,General Services Administration,Washington,D.C.HACK AND BAND SAW MANUFACTURERS ASSOCIATION OF AMERICA RichardSchrade,Ciemson Brothers,Inc.,Middletown,New York C.M.Srockinger,Alternate,Hack&Band Saw Manufacturers Association of America,Cleveland,Ohio METAL CUTTING TOOL INSTITUTE W.A.Wagner,Cleveland Twist Drill Company,Cleveland,Ohio R.M.Byrne,Alternate,Metal Cutting Tool Institute,New York,New York NATIONAL ASSOCIATION OF PUNCH MANUFACTURERS To Be Appointed NATIONAL BUREAU OF STANDARDS To Be Appointed NATIONAL MACHINE TOOL BUILDERS ASSOCIATION G.F.Wilson,General Electric Company,Worthington,Ohio E.J.Loeffler,Alternate,National Machine Tool Builders Association,McLean,Virginia SOCIETY OF CARBIDE ENGINEERS C.H.Lang,c/o Society of Carbide Engineers,Bridgeville,Pennsylvania SOCIETY OF MANUFACTURING ENGINEERS K.A.Lundell,The Product0 Machine Company,Jamestown,New York Harry McLinden,Caterpillar Tractor Company,Peoria,Illinois W.N.Moore,The Ford Motor Company,Dearborn,Michigan TELEPHONE GROUP,THE R.A.Agnew,Western Electric Company,Inc.,Chicago,Illinois S.P.Rogacki,Alternate,Western Electric Company,Inc.,Kearney,New Jersey U.S.DEPARTMENT OF THE AIR FORCE To be appointed i v Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.U.S.DEPARTMENT OF THE ARMY D.L.York,Liaison,General Thomqs J.Rodman Laboratories,Rock Island,Illinois U.S.DEPARTMENT OF THE NAVY J.R.Ruff,Liaison,Naval Ship Systems Command,Washington,D.C.U.S.MACHINE SCREW BUREAU Herman Muenchinger,Continental Screw Company,New Bedford,Massachusetts D.E.Chase,Alternate,Continental Screw Company,New Bedford,Massachusetts INDIVIDUAL COMPANIES Harold Cooper,Chrysler Corporation,Detroit,Michigan Kenneth Hull,The Ingersoll Milling Machine Company,Rockford,Illinois A.M.Mezey,Richard Brothers Punch Company,Detroit,Michigan Lyle Srorrer,Mohawk Tools,Inc.,Montpelier,Ohio INDIVIDUAL MEMBERS Anderson Ashburn,American Machinist,New York,New York