ASME_B89.4.1-1997.pdf

AN AMERICAN NATIONAL STANDARD ASME 889.4.1 b-2001 ADDENDA to ASM E B89.4.1-1997 METHODS FOR PERFORMANCE EVALUATION OF COORDINATE MEASURING MACHINES THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS Three Park Avenue New York,NY 10016 Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Date of Issuance:February 8,2002 ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American National Standards.The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate.The proposed code or standard was made available for public review and comment which provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not approve,rate,or endorse any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable Letters Patent,nor assume any such liability.Users of a code or standard are expressly advised that determination of the validity of any such patent rights,and the risk of the infringement of such rights,is entirely their own responsibility.Participation by federal agency representative(?.)or person(s)affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations issued in accordance with governing ASME procedures and policies which preclude the issuance of interpretations by individual volunteers.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical Engineers Three Park Avenue,New York,NY 10016-5990 Copyright O 2002 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All Rights Reserved Printed in U.S.A.Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ASME B89.4.1 b-2001 Following approval by the ASME B89 Committee and ASME,and after public review,ASME B89.4.1 b-2001 was approved by the American National Standards Institute on August 31,2001.Addenda to the 1997 edition of ASME B89.4.1 are issued in the form of replacement pages.Revisions,additions,and deletions are incorporated directly into the affected pages.It is advisable,however,that this page,the Addenda title and copyright pages,and all replaced pages be retained for reference.SUMMARY OF CHANGES This is the second addenda to be published to ASME B89.4.1-1997.A previous addenda was published in 1998.Replace or insert the pages listed.Changes listed below are identified on the pages by a margin note,(b),placed next to the affected area.Previous addenda changes are indicated by(a).The pages not listed are the reverse sides of the affected pages and contain no changes.Page vi.i vii-ix Location Change Correspondence With the B89 Added Committee Contents Updated to reflect Addenda 1 Section 1 2 1.1 4 Fig.IA 7-7.2 Fig.1C 31,31.1 5.5.I 36 46 47 49 50 5.5.2.3 5.6.2 5.6.3 Section 6 6.2 Table 3 Fig.38 Fourth paragragh,last two lines added Subparagraph(d)revised Subcategory Settling Time revised(1)First page revised(2)Second and third page added(1)First paragraph revised(2)Subparagraphs(a)through(d)added Third sentence added(I)Penultimate sentence revised(2)Last sentence added First sentence revised(I)Title editorially revised(2)Last sentence revised Revised in its entirety Added Added Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 50,51 51 52 52.i Location 6.2.1 6.2.2 6.3 Table 4 Table 5 Table 6 Table 7 6.3.1 6.3.2 6.3.3 6.4 6.4.1 6.4.2 Change Revised in its entirety Revised in its entirety Added Added Added Added Added Added Added Added Added Added Added Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CORRESPONDENCE WITH THE B89 COMMITTEE General.ASME Codes and Standards are developed and maintained with the intent to represent the consensus of concerned interests.As such,users of this Standard may interact with the Committee by requesting interpretations,proposing revisions,and attending Committee meetings.Correspondence should be addressed to:Secretary,B89 Main Committee The American Society of Mechanical Engineers Three Park Avenue New York,NY 10016 Proposed Revisions.Revisions are made per