ASME_B94-35-1972-R2005.PDF

A M E R I C A N N A T I O N A L S T A N D A R D DriII Drivers,Split-Sleeve,CoIIet Type ANSI B94.35-1972 REVISION OF ANSI 894.35-1959 (R1971)I REAFFIRMED 1995 FOR CURRENT COMMllTEE PERSONNEL PLEASE SEE ASME MANUAL A S 1 1 THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLISHED BY T H E A M E R I C A N S O C I E T Y O F M E C H A N I C A L E N G I N E E R$United Engineering Center 345 East 47th Street New York,N.Y.1 001 7 Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.REAFFIRMED 2005FOR CURRENT COMMITTEE PERSONNELPLEASE E-MAIL CSasme.orgAny part of this standard may be quoted.Credit lines should read:”Extracted from American National Standard Drill Drivers-Split Sleeve,Collet Type,ANSI B94.35-1972,with the permission of the publisher,The American Society of Mechanical Engineers,345 East 47th Street,New York,N.Y.10017.”Copyright,01972.by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS Printed in U.S.A.Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.FOREWORD Throughout American industry a variety of methods and mechanisms are used to drive twist drills,reamers,etc.In the automotive and other mass production industries,the split-sleeve collet drive has proven useful.Two engineering reasons for its suitability are:(1)Multiple spindle drill heads can be designed with spindles on a very close center-to-center distance;(2)Bushing plates do not have to be moved when tools must be replaced.The splitsleeve collet driver is designed to drive straight shanks in sizes$61(0.0390)inch diameter and larger.As the assembly of split sleeve collet-type driver necessitates manufacture to close tolerances,it was deemed advisable to develop an American standard to insure that collets would fit drill shanks as shown in ANSI 894.1 1-1967.The required ASA approval and designation as American Standard Drill Drivers was granted on September 23,1959,and designated ASA 85.27-1959.ASA B5.27-1959 was redesignated and reaffirmed as ANSI B94.35-1959(R1971).ANSI 894.35-1959 (R1971)was reviewed in relation to industry needs and revised and updated by a subcommittee of Technical Committee 7 of American National Standards Committee 894.Sizes no longer used were eliminated from the standard.Document was reviewed for con-formance with American National Standard Decimal Inch,ANSI B87.1-1965.The current revision was approved by ANSI on May 30,1972.iii Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.AMERICAN NATIONAL STANDARDS COMMITTEE B94 STANDARDIZATION OF CUTTING TOOLS,HOLDERS,DRIVERS 81 BUSHINGS(The following is the roster of the Committee at the time of approval of this standard)OFFICERS H.J.Moffatt,Chairman A.M.Mezey,Vice-chairman H.McLinden,Secretary STANDARDS COMMITTEE AMERICAN GEAR MANUFACTURERS ASSOCIATION,THE P.M.Dean,Jr.,Mechanical Technology,Inc.,Latham,New York G.L.Scott,Alternate,American Gear Manufacturers Association,Washington,D.C.AMERICAN SOCIETY OF MECHANICAL ENGINEERS,THE M.E.Merchant,Cincinnati Milacron,Inc.,Cincinnati,Ohio G.M.Monacelli,General Electric Company,Detroit,Michigan C.J.Oxford,Jr.,National Twist Drill&Tool Company,Rochester,Michigan CEMENTED CARBIDE PRODUCERS ASSOCIATION W.E.Montgomery,Firth Sterling,Inc.,McKeesport,Pennsylvania A.P.Wherry,Alternate,Cemented Carbide Producers Association,Cleveland,Ohio GENERAL SERVICES ADMINISTRATION W.C.Petrie,General Services Administration,Washington,D.C.METAL CUTTING TOOL INSTITUTE L.P.Sohles,Morse Twist Drill&Machine Company,New Bedford.Massachusetts P.L.Houser,Alternate,Metal Cutting Tool Institute,New York,New York NATIONAL ASSOCIATION OF PUNCH MANUFACTURERS R.J.Gargrave,Dayton Progress Corporation,Dayton,Ohio NATIONAL BUREAU OF STANDARDS J.R.Pidgeon,National Bureau of Standards,Washington,D.C.SOCIETY OF AUTOMOTIVE ENGINEERS A.J.McLaren,The Cross Company,Fraser,Michigan W.H.Seacord,International Harvester Company,Hinsdale,IlJinois SOCIETY OF CARBIDE ENGINEERS C.H.Lang,Society of Carbide Engineers,Milford,Connecticut SOCIETY OF MANUFACTURING ENGINEERS K.A.Lundell,The Product0 Machine Company,Jamestown,New York H.J.Moffart,Caterpillar Tractor Co.,East Peoria,Illinois TELEPHONE GROUP M.C.Berryman,Western Electric Company,Inc.,Chicago,Illinois S.P.Rogacki,Alternate,Western Electric Company,Inc.,Kearney,New Jersey UNITED STATES DEPARTMENT OF THE AIR FORCE J.O.Snyder,Liaison,Air Materials Laboratory,Wright-Patterson Air Force Base,Ohio UNITED STATES DEPARTMENT OF THE ARMY R.K.Freeman,Liaison,United States Weapons Command,Rock Island,Illinois J.M.Segura,Alternate,United States Weapons Command,Rock Island,Illi