分享
ASME_B94-2-1995.pdf
下载文档

ID:167706

大小:3.95MB

页数:72页

格式:PDF

时间:2023-03-03

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
ASME_B94 1995
Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.AN AMERICAN NATIONAL STANDARD REAMERS ASME B94.2-I995(REVISION OF ANSI 694.2-1983)The American Society of Mechanical Engineers 345 East 47 th Street,New York,N.Y.Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.Date of Issuance:July 31,1995 This Standard will be revised when the Society approves the issuance of a new edition.There will be no addenda or written interpretations of the requirements of this Standard issued to this edition.ASME is the registered trademark of the American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American National Standards.The Consensus Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate.The proposed code or standard was made available for public review and comment which provides an opportunity for additional public input from industry,academia,regulatory agen-cies,and the public-at-large.ASME does not approve,rate,or endorse any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable Letters Patent,nor assume any such liability.Users of a code or standard are expressly advised that determination of the validity of any such patent rights,and the risk of infringement of such rights,is entirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations issued in accordance with governing ASME procedures and policies which preclude the issuance of interpretations by individual volun-teers.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.Copyright 0 1995 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All Rights Reserved Printed in USA.Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.FOREWORD This Standard for reamers was formulated by Technical Committee 20 of the B5 Sectional Committee on the Standardization of Small Tools and Machine Tool Elements.The organization of Technical Committee 20 on the Standardization of Reamers in March 1937 was prompted by a recognized need for unifying the practice in this field.The proposal submitted by the committee was approved by ASA and designated ASA B5.14-1941.The Standard ASA B5.14-1941 was revised and approved in 1949,and sub-sequently reaffirmed in 1954.A sufficient number of requests for revision resulted in reactivation of the committee in 1957.The revision was approved by the sectional com-mittee and the sponsors,and the required ASA approval and designation were granted April 9,1959.In November 1961,the ASA Mechanical Standards Board approved the request of the B5 Sectional Committee sponsors that a separate project be initiated under ASA Procedure on the subject of Cutting Tools.As a result of this action,a new project was initiated on Cutting Tools,and ASME accepted sponsorship.The committee was designated B94 Cutting Tools,and the activity on cutting tools was removed from the B5 Sectional Committee.The designation numbers of the technical committees were changed to con-form with the new sectional committee organization.B5 Technical Committee 20 was changed to B94 Technical Committee 9.Requests for revision to B5.14-1959 to cover additions,deletions,and clarification of the Standard necessitated reactivation of the committee.The revised draft was prepared and distributed to the members for review and comment.A meeting of TC-9 was held in November 1962,and the draft was subsequently approved by the committee.The revised Standard was submitted to Sectional Committee B94 on May 27,1964.Following approval by the Sectional Committee and the sponsor,the Standard was ap-proved by ASA on December 21,1964 and designated as ASA B94.2-1964.In 1970,Technical Committee 9 revised the 1964 issue of B94.2,incorporating revisions and additions reflecting current industry practice.The revision was presented to American National Standards Committee B94 and to the B94 secretariat for approval

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开