ASME_B5-60-2002.pdf

ASME B5.60-2002WORKHOLDINGCHUCKS:JAWTYPE CHUCKSIncorporating ASME B5.60.1 and ASME B5.60.4A N A M E R I C A N N A T I O N A LS T A N D A R DASME B5.60-2002WORKHOLDINGCHUCKS:JAWTYPE CHUCKSIncorporating ASME B5.60.1 and ASME B5.60.4A N A M E R I C A N N A T I O N A LS T A N D A R DCopyright 2009 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.AN AMERICAN NA TIONALST ANDARDWORKHOLDINGCHUCKS:JAW TYPE CHUCKSIncorporating ASME B5.60.1 and ASME B5.60.4ASME B5.60-2002Copyright 2009 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.Date of Issuance:September 16,2002The 2002 edition of this Standard is being issued with an automatic addendasubscription service.The use of addenda allows revisions made in responseto public review comments or committee actions to be published asnecessary.The next edition of this Standard is scheduled for publication in2005.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria forAmerican National Standards.The Standards Committee that approved the code or standardwas balanced to assure that individuals from competent and concerned interests have had anopportunity to participate.The proposed code or standard was made available for public reviewand comment that provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted inconnection withany itemsmentioned inthis document,and doesnot undertaketo insureanyoneutilizing a standardagainst liability for infringementof any applicable letterspatent,nor assumesany such liability.Users of a code or standard are expressly advised that determination of thevalidity of any such patent rights,and the risk of infringement of such rights,is entirely theirown responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not tobe interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued inaccordance with the established ASME procedures and policies,which precludes the issuanceof interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright 2002 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll Rights ReservedPrinted in U.S.A.Copyright 2009 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.CONTENTSForeword.ivStandards Committee Roster.vCorrespondence With the B5 Committee.viPreface.viiASME B5.60.1General Description and Definitions of Terms.1ASME B5.60.2Chuck-to-Spindle Interface(to be added)ASME B5.60.3Jaw Mountings(to be added)ASME B5.60.4Performance Testing.5ASME B5.60.5Safety Code of Practice(to be added)ASME B5.60.6Chuck Assembly:Sizes and Designation(to be added)iiiCopyright 2009 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.FOREWORDDuring the review,revision,and update of the existing inch-based American NationalStandard B5.8 on Chucks and Chuck Jaws,Technical Committee 11 of the ASME B5Committee on Machine Tools recognized the need for an industry standard on metric-dimensioned chucks.This Standard was developed after reviewing currently available national and internationalstandards,which were used as its foundation.B50.60.1 and B5.60.4 were completed in November 1999 and submitted to ASME.The standard titled,Workholding Chucks:Jaw Type Chucks,comprises six parts,witheach covering a specific aspect of workholding chu