ASME_B94.13-1976.pdf

_-9009275 0024145 794 H A M E R I C A N N A T I O N A L S T A N D A R D Blanks for Carbide Burs ANSI B94.13-1976(REVISION OF USAS 894.13-1968)SECRETARIAT THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLISHED BY T H E A M E R I C A N S O C I E T Y O F M E C H A N I C A L E N G I N E E R S United Engineering Center New York,N.Y.1 O 0 1 7 345 East 47th Street Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:46:29 MSTNo reproduction or networking permitted without license from IHS-,-,-m 9009275 0024346 620 U No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the pub1 isher,Copyright O 1976 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS Ali Rights Reserved Printed in U.S.A.Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:46:29 MSTNo reproduction or networking permitted without license from IHS-,-,-7007275 0024347 567 FOREWORD The material contained in the following pages of this standard was developed by the Standard Committee of the Cemented Carbide Producers Association in cooperation with the Solid Carbide Tool Institute.The dimensional listings together with tolerances and nomenclature have been de-veloped after a thorough investigation of ail factors involved in the field of blanks for carbide burs.The original draft of the material was prepared by the Solid Carbide Tool Institute and submitted to the Cemented Carbide Producers Association for review and comment.The final draft as represented by the material contained in this standard was reviewed by both organizations and by all interested parties and was revised to incorporate the changes suggested.On January 20,1959,the Cemented Carbide Producers Association submitted the final draft of the standard to ASA for approval under the Existing Standards Method.Ac-cordingly,a canvass of industry was made to meet the requirement that evidence be shown that the standard is acceptable to those groups substantially concerned with its technical con-tent.The proposal was approved as an American Standard on October 23,1962.Meanwhile in 1962,a new Sectional Committee B94 Standardization of Cutting Tools,Holders,Drivers and Bushings was formed(later changed to USA Standards Committee)and the work on this standard was assigned to Technical Committee 1 of USA Standards Com-mittee B94.The revised standard was approved by USA Standards Committee B94 and its sponsor ASME on November 2,1967.The revision was approved by USA Standards Institute on January 12,1968 and redesignated USAS 894.13-1968.A second revision was approved as an American National Standard on March 29,1976 and designated B94.13-1976.Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:46:29 MSTNo reproduction or networking permitted without license from IHS-,-,-7009275 0024148 4T3 AMERICAN NATIONAL STANDARDS COMMITTEE 694 Standardization of Cutting Tools,Holders,Drivers and Bushings(The following is the roster of the committee at the time of the approval of the standard)OFFICERS Harry McLinden,Chairman A.H.Merey,Vice-chairman Kurt Weaely,Secretary STANDARDS COMM ITTEE AMERICAN GEAR MANUFACTURERS ASSOCIATION,THE P.M.Dean,Jr.,Mechanical Technology,Inc.,Latham,New York G.L.Scott,Alternate,American Gear Manufacturers Association,Washington,D.C.AMERICAN SOCIETY OF MECHANICAL ENGINEERS,THE M.E.Merchant,Cincinnati Milacron,Inc.,Cincinnati,Ohio G.M.Monacelli,General Electric Company,Detroit,Michigan C.J.Oxford,Jr.,National Twist Drill&Tool Company,Rochester,Michigan C.F.Wilson,Alternate,DoAU Company,Des Plaines,Illinois W.E.Montgomery,Firth Sterling,Inc.,McKeesport,Pennsylvania A.P.Wherry,Alternate,Cemented Carbide Producers Association,Cleveland,Ohio CEMENTED CARBIDE PRODUCERS ASSOCIATION GENERAL SERVICES ADMINISTRATION W.Wacker,General Services Administration,Washington,D.C.Richard Schrede,Clemson Bros.,Inc.,Middletown,New York J.E.Bates,Alternate,Hack&Band Saw Manufacturers Association,Mt.Prospect,Illinois HACK&BAND SAW MANUFACTURERS ASSOCIATION OF AMERICA METAL CUTTING TOOL INSTITUTE W.A.Wagner,Cleveland Twist Drill Company,Cleveland,Ohio.M.Byrne,Alternate,Metal Cutting Tools Institute,New York,New York.E.Smith,Dayton Progress Corporation,Dayton,Ohio NATIONAL ASSOCIATION OF PUNCH MANUFACTURERS NATIONAL BUREAU OF STANDARDS J.Pidgeon,National Bureau of Standards,Washuigton,D.C.NATIONAL MACHINE TOOL BUILDERS ASSOCIATION C.F.Wilson,DoAll Company,Des Plaines,Illinois E.J.Loeffler,Alrernare,National Machine Tool Builders Association,McLean,Virginia SOCIETY OF AUTOMOTIVE ENGINEERS To be appointed.C.H.Lang,c/o Society of Carbide Engineers,Bridgeville,Pennsylvania K.A.Lundell,The Producto Machine Company,J