47-1_Edtn_2007.pdf

Gage BlanksAN AMERICAN NATIO NAL STANDARDASME B47.1-2007(Revision of ASME/ANSI B47.1-1988)Copyright 2008 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ASME B47.1-2007(Revision of ASME/ANSI B47.1-1988)Gage BlanksAN AMERICAN NATIONAL STANDARDThree Park Avenue New York,NY 10016Copyright 2008 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.Date of Issuance:April 7,2008This Standard will be revised when the Society approves the issuance of a new edition.There willbe no addenda or written interpretations of the requirements of this Standard issued to this edition.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American NationalStandards.The Standards Committee that approved the code or standard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participate.The proposed code or standard was madeavailable forpublic review andcomment thatprovides an opportunityfor additional publicinput from industry,academia,regulatory agencies,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with anyitems mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability forinfringement of any applicable letters patent,nor assume any such liability.Users of a code or standard are expresslyadvised that determination of the validity of any such patent rights,and the risk of infringement of such rights,isentirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted asgovernment or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the establishedASME procedures and policies,which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright 2008 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.Copyright 2008 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.CONTENTSForeword.viiCommittee Roster.ixCorrespondence With the B47 Committee.x1Scope.12Terminology.13Details of Construction American Gage Design Standards.34Official Monogram for Designating Products Made to American Gage DesignStandards.75Application of American Gage Design Standards to Special Types ofGages Recommended Practice.76Flush Pin Gages.77Double-End Built-Up Snap Gages.78Flat Plug Gages.79Handles,Bilock,for Flat Plug Gages.8Figures1Plain Cylindrical Plug Gages,Details of Construction Range Above0.010 in.to and Including 8.010 in.92Plain Cylindrical Plug Gages,Details of Construction Range Above8.010 in.243Thread Plug Gages Details of Construction.264Plain Ring Gages Details of Construction.405Thread Ring Gage Locking Device,Details of Construction Range 1 in.to 512in.,Inclusive.436Thread Ring Gages,Details of Construction Range 0.060 in.to andIncluding 4.760 in.457Thread Ring Gages,Details of Construction Range Above 0.510 in.to andIncluding 12.260 in.468Three-Piece Spline Plug Gage Assembly.619Spline Plug Gage Stands.6210Adjustable Snap Gages,Details of Construction Models A,B,C,and MC.8311Adjustable Snap Gages,Details of Construction Model E.8312Model MC Snap Gage Details.8913Adjustable Length Gage,Double Sided,Models KA and KB,Details ofConstruction.9814Adjustable Length Gage,Progressive,Models LA and LB,Details ofConstruction.9915Adjustable Length Gage,Double Sided,Model KA,Details of Gage Heads.10016Adjustable Length Gage,Double Sided,Model KB,Details of Gage Heads.10117Adjustable Length Gage,Progressive,Model LA,Details of Gage Heads.10218Adjustable Length Gage,Progressive,Model LB,