2002_w_err_2002.pdf

Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.AN AMERICAN NA TIONALST ANDARDGAGE BLOCKSASME B89.1.9-2002Revision of ANSI/ASME B89.1.9-1984(R1997)Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ErratatoASME B89.1.9-2002Gage BlocksThe errata corrections listed below apply to ASME B89.1.9-2002.Corrected figures and tablesfollow.PageLocationChange3Fig.1BDimensions revised;reference point added tosecond and last drawings4Table 1aEntries in last three columns revised5Table 1bEntries in last three columns revisedFig.5(1)?deleted from top callout(2)0.02 and 0.03 revised to read 0.2 and 0.3,respectively14Table B1 replaced by in four placesTable B3 replaced by in six places26Table G1(1)In last column,18th through 29th entriesrevised(2)In last row,first five entries revisedTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSThree Park Avenue,New York,NY 10016-5990December 2003L4402ECopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.GAGE BLOCKSERRATA TO ASME B89.1.9-20021/2 width1/2 distance between edgeof block and edge ofcountersink1/2 distance between edgeof block and edge ofcountersink1/2 width25302.012.012.01FIG.1BREFERENCE POINTS OF SQUARE GAGE BLOCKSTABLE 1aDIMENSIONS IN MILLIMETERSa(width)b(depth)Cross SectionNominal length,lnNominalToleranceNominalToleranceSquare0 to 100024.10.224.10.2Rectangle0.5 up to 1030+0.0/0.390.05/0.20Over 10 up to 100035+0.0/0.390.05/0.20GENERAL NOTE:Square gage blocks have a 6.7 mm 0.1 mm center hole.The hole iscountersunk on both sides 70 deg to 84 deg for blocks 5 mm and longer.Blocks under 5 mmare not countersunk.TABLE 1bDIMENSIONS IN INCHESa(width)b(depth)Cross SectionNominal Length,lnNominalToleranceNominalToleranceSquare0 to 400.95 0.010.95 0.01Rectangle0.01 to 0.21.181+0.0740.355+0.020 0.084 0.010Over 0.2 up to 401.378+0.0100.355+0.020 0.207 0.010GENERAL NOTE:Square gage blocks have a 0.265 0.010 in.center hole.The hole is counter-sunk on both sides 70 deg to 84 deg for blocks 0.2 in.and longer.Blocks under 0.2 in.are notcountersunk.Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.GAGE BLOCKSERRATA TO ASME B89.1.9-2002YXB2535AA BAY-AxisX-AxisE10+0.2010.3BFIG.5DIMENSIONS OF COUPLING HOLES(mm)TABLE B1EXAMPLE OF TOLERANCECHANGESSizeGGG-G-15CThis Standard1 mmGrade 2,+0.10/0.05?mGrade 0,0.12?m75 mmGrade 3,+0.45/0.22?mGrade AS-1,0.50?m0.1 in.Grade 2,+4/2?in.Grade 0,5?in.2.0 in.Grade 3,+16/8?in.Grade AS-1,16?in.TABLE B3LENGTH TOLERANCECOMPARISONSizeGGG-G-15CThis Standard1 mmGrade 1,0.05?mGrade AS-1,0.20?m75 mmGrade 2,+0.25/0.12?mGrade AS-2,1.00?m0.1 in.Grade 1,2?in.Grade AS-1,8?in.1.0 in.Grade 2,+4/2?in.Grade AS-2,24?in.Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.GAGE BLOCKSERRATA TO ASME B89.1.9-2002TABLE G1INCH GAGE BLOCK SIZES(IN INCHES)0.00550.02020.0520.10070.1300.200080.0060.02030.0530.10080.1310.200090.00650.02040.0540.10090.1320.2500.0070.02050.0550.1010.1330.3000.00750.02060.0560.1020.1340.3500.0080.02070.0570.1030.1350.4000.00850.02080.0580.1040.1360.4500.0090.02090.0590.1050.1370.5000.00950.0210.0600.1060.1380.5500.0100.0220.06250.1070.1390.6000.010050.0230.0700.1080.1400.6500.01010.0240.0781250.1090.1410.7000.01020.0250.0800.1093750.1420.7500.01030.0260.0900.1100.1430.8000.01040.0270.093750.1110.1440.8500.01050.0280.1000.1120.1450.9000.01060.0290.100010.1130.1460.9500.01070.0300.100020.1140.1471.0000.01080.031250.1000250.1150.1482.0000.01090.0400.100030.1160.1493.0000.0110.0468750.100040.1170.1504.0000.0120.0500.100050.1180.1605.0000.0130.050050.100060.1190.1706.0000.0140.05010.100070.1200.1807.0000.0150.05020.1000750.1210.1908.0000.0156250.05030.100080.1220.20010.0000.0160.05040.100090.1230.2000112.0000.0170.05050.10010.1240.2000216.0000.0180.05060.10020.1250.2000320.0000.0190.05070.10030.1260.20004.0.0200.05080.10040.1270.20005.0.020050.05090.10050.1280.20006.0.02010.0510.10060.1290.20007.Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.Date of Issuance:July 12,2002The next edition of this Standard is scheduled for publication in 2007.Therewill be no addenda or written interpretations of the requirements of thisStandard issu