温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
ASME_B30
10
2019
AN AM E R IC AN NAT IO NAL STANDARDASME B30.10-2019(Revision of ASME B30.10-2014)HooksSafety Standard for Cableways,Cranes,Derricks,Hoists,Hooks,Jacks,and SlingsASME B30.10-2019(Revision of ASME B30.10-2014)HooksSafety Standard for Cableways,Cranes,Derricks,Hoists,Hooks,Jacks,and SlingsAN AMERICAN NATIONAL STANDARDxDate of Issuance:November 21,2019ThenexteditionofthisStandardisscheduledforpublicationin2024.ThisStandardwillbecomeeffective1yearaftertheDateofIssuance.ASME issues written replies to inquiries concerning interpretations of technical aspects of this Standard.Interpretations arepublished on the ASME website under the Committee Pages at http:/cstools.asme.org/as they are issued.Errata to codes and standards may be posted on the ASME website under the Committee Pages to provide corrections toincorrectlypublisheditems,ortocorrecttypographicalorgrammaticalerrorsincodesandstandards.Sucherratashallbeusedon the date posted.TheCommitteePagescanbefoundathttp:/cstools.asme.org/.Thereisanoptionavailabletoautomaticallyreceiveane-mailnotification when errata are posted to a particular code or standard.This option can be found on the appropriate CommitteePage after selecting“Errata”in the“Publication Information”section.ASME is the registered trademark of The American Society of Mechanical Engineers.ThiscodeorstandardwasdevelopedunderproceduresaccreditedasmeetingthecriteriaforAmericanNationalStandards.TheStandardsCommitteethatapprovedthecodeorstandardwasbalancedtoassurethatindividualsfromcompetentandconcernedinterestshavehadanopportunityto participate.The proposed codeorstandardwasmadeavailable forpublic reviewandcommentthatprovidesanopportunityfor additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in thisdocument,anddoesnotundertaketoinsureanyoneutilizingastandardagainstliabilityforinfringementofanyapplicableletterspatent,norassumeanysuchliability.Usersofacodeorstandardareexpresslyadvisedthatdeterminationofthevalidityofanysuchpatentrights,andtherisk of infringement of such rights,is entirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted as government or industryendorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME proceduresand policies,which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersTwo Park Avenue,New York,NY 10016-5990Copyright 2019 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.CONTENTSForeword.vCommittee Roster.viB30 Standard Introduction.viiiSummary of Changes.xiChapter 10-0Scope,Definitions,References,Personnel Competence,and Translations.1Section 10-0.1Scope of ASME B30.10.1Section 10-0.2Definitions.1Section 10-0.3References.1Section 10-0.4Personnel Competence.2Section 10-0.5Translations.2Chapter 10-1Hooks:Selection,Use,and Maintenance.3Section 10-1.1Scope.3Section 10-1.2Training.3Section 10-1.3Materials and Components.3Section 10-1.4Fabrication and Configurations.3Section 10-1.5Design Factor.3Section 10-1.6Rated Loads.3Section 10-1.7Proof Test Requirements.3Section 10-1.8Identification.4Section 10-1.9Effects of Environment.4Section 10-1.10Inspection,Removal,and Repair.4Section 10-1.11Operating Practices.6Chapter 10-2Hooks Miscellaneous:Selection,Use,and Maintenance.10Section 10-2.1Scope.10Section 10-2.2Training.10Section 10-2.3Materials and Components.10Section 10-2.4Fabrication and Configurations.10Section 10-2.5Design Factor.10Section 10-2.6Rated Loads.10Section 10-2.7Proof Test Requirements.10Section 10-2.8Identification.10Section 10-2.9Effects of Environment.11Section 10-2.10Inspection,Removal,and Repair.11Section 10-2.11Operating Practices.12Figures10-1.1-1Clevis Hook(Latch When Required).610-1.1-2Eye Hook(Latch When Required).7iii10-1.1-3Shank Hook(Latch When Required).710-1.1-4Duplex Hook(Sister)(Latch When Required).710-1.1-5Articulated Duplex Hook(Sister)(Latch When Required).710-1.1-6Self-Locking Eye Hook(Open).710-1.1-7Self-Locking Clevis Hook(Closed).710-1.1-8Self-Closing Bail(Eye Hook).810-1.1-9Self-Closing Gate Latch(Shank Hook).810-1.1-10Self-Closing Flapper Latch(Shank Hook).810-1.1-11Self-Closing Flapper Latch(Swivel Hook).810-1.1-12Self-Closing Flipper Latch(Eye Hook).810-1.1-13Self-Closing Tiplock Latch(Shank Hook).810-1.1-14Self-Closing Tiplock Latch(Eye Hook).910-1.1-15Single Plate Hook.910-1.1-16Laminated Plate Hook.910-1.1-17Quad Hook(Latch When Required).910-2.1-1Eye Grab Hook.1210-