18-5_Edtn_2008.pdf

Round Head Bolts(Inch Series)AN AMERICAN NATIO NAL STANDARDRevision of ASME B18.5-1990(R2003)ASME B18.5-2008Copyright 2008 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ASME B18.5-2008Revision of ASME B18.5-1990(R2003)Round Head Bolts(Inch Series)AN AMERICAN NATIONAL STANDARDCopyright 2008 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.Date of Issuance:September 5,2008This Standard will be revised when the Society approves the issuance of a new edition.There willbe no addenda issued to this edition.ASME issues written replies to inquiries concerning interpretations of technical aspects of thisdocument.Periodically,certain actions of the ASME B18 Committee may be published as Cases.Cases and interpretations are published on the ASME Web site under the Committee Pages athttp:/cstools.asme.org as they are issued.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American NationalStandards.The Standards Committee that approved the code or standard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participate.The proposed code or standard was madeavailable forpublic review andcomment thatprovides an opportunityfor additional publicinput from industry,academia,regulatory agencies,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with anyitems mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability forinfringement of any applicable letters patent,nor assume any such liability.Users of a code or standard are expresslyadvised that determination of the validity of any such patent rights,and the risk of infringement of such rights,isentirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted asgovernment or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the establishedASME procedures and policies,which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright 2008 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.Copyright 2008 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.CONTENTSForeword.ivCommittee Roster.vCorrespondence With the B18 Committee.vi1Introductory Notes.12General Data.2Tables1Dimensions of Round Head Bolts.42Dimensions of Round Head Square Neck Bolts.53Dimensions of Round Head Short Square Neck Bolts.64Dimensions of Round Head Ribbed Neck Bolts.75Dimensions of Round Head Fin Neck Bolts.86Dimensions of Step Bolts.97Dimensions of Countersunk Bolts and Slotted Countersunk Bolts.108Dimensions of 114-deg Countersunk Square Neck Bolts.119Dimensions of Flat Countersunk Head Elevator Bolts.1210Dimensions of T-Head Bolts.13iiiCopyright 2008 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.FOREWORDAmerican National Standards Committee B18 for the standardization of bolts,screws,nuts,rivets,and similar fasteners was originated in March 1922 as Sectional Committee B18,underthe aegis of the American Engineering Standards Committee later the American StandardsAssociation,the United States of America Standards Institute,and as of October 6,1969,theAmerican National Standards Institute,Inc.(ANSI),with the Society of Automotive Engineer