0-1M_R2005_E2000.pdf

ASME B18.30.1M-2000OPEN-END BLIND RIVETS WITH BREAK MANDRELS(METRIC SERIES)A N A M E R I C A N N A T I O N A LS T A N D A R DASME B18.30.1M-2000OPEN-END BLIND RIVETS WITH BREAK MANDRELS(METRIC SERIES)A N A M E R I C A N N A T I O N A LS T A N D A R DB18.30.1M-2000 5/10/00 2:47 PM Page 1Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.REAFFIRMED 2005FOR CURRENT COMMITTEE PERSONNELPLEASE E-MAIL CSasme.orgAN AMERICAN NA T I O N A LS T A ND A R DOPEN-END BLIND RIVETSWITH BREAK MANDRELS(METRIC SERIES)ASME B18.30.1M-2000B18.30.1M-2000 5/10/00 2:48 PM Page 3Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.p.105-25-00 12:19:20Unit:ucpTextfile:b18301$cpep.1Date of Issuance:June 30,2000This Standard will be revised when the Society approves the issuance ofa new edition.There will be no addenda or written interpretations of therequirements of this Standard issued to this edition.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria forAmerican National Standards.The Standards Committee that approved the code or standardwas balanced to assure that individuals from competent and concerned interests have had anopportunity to participate.The proposed code or standard was made available for public reviewand comment that provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted inconnection withany itemsmentioned inthis document,and doesnot undertaketo insureanyoneutilizing a standard against liability for infringement of any applicable letters patent,nor assumeany such liability.Users of a code or standard are expressly advised that determination of thevalidity of any such patent rights,and the risk of infringement of such rights,is entirely theirown responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not tobe interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued inaccordance with the established ASME procedures and policies,which precludes the issuanceof interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright 2000 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll Rights ReservedPrinted in U.S.A.Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.p.305-25-00 12:19:36Unit:ufwTextfile:b18301$fwp.3FOREWORDIn 1994,ASME established the B18.30 subcommittee.This subcommittee was initiallyformed to develop U.S.standards for blind rivets.After the first meeting however,it wasrecommended that the subcommittee should develop standards for all blind fasteners.The first endeavor by this subcommittee was to create U.S.standards for metric blindrivets,followed by U.S.standards for inch blind rivets.It was further recommended thatthe U.S.committee consider input based on the International Standards Organization(ISO)and the Industrial Fastener Institute(IFI).The latter organization was the first to establishwell-documented,dimensional and mechanical properties for blind rivets.Therefore,muchof the data in the IFI standards was used to prepare this standard.ASME B18.30.1M-2000 was approved by the American National Standards Institute(ANSI)on February 29,2000.iiiCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.This page intentionally left blank.Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.p.507-03-01 14:57:04Unit:UCRTextfile:B18301$crp.5ASME B18 STANDARDS COMMITTEEStandardization of Bolts,Nuts,Rivets,Screws,Washers,and Similar Fasteners(The following is the roster of the Committee at the time of approval of this Standard.)OFFICERSD.A.Clever,ChairR.D.Strong,Vice ChairS.W.Vass,Vice ChairR.L.Crane,SecretaryCOMMITTEE PERSONNELJ