分享
ASME_B16.15-2006.pdf
下载文档

ID:167160

大小:3.94MB

页数:38页

格式:PDF

时间:2023-03-03

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
ASME_B16 15 2006
FOREWORDAs early as the spring of 1921,the consolidation and further development of threaded andflanged fittings standards in force in this country seemed desirable.To meet this need,theAmerican Standards Association(ASA)now the American National Standards Institute(ANSI)authorized the organization of a Sectional Committee on the Standardization of Pipe Flangesand Flanged Fittings(B16),with the Heating,Piping,and Air Conditioning ContractorsNationalAssociation(now known as the Mechanical Contractors Association of America),the Manufactur-ers Standardization Society of the Valve and Fittings Industry(MSS),and The American Societyof Mechanical Engineers acting as joint sponsors.In June 1927,the Manufacturers Standardization Society of the Valve and Fittings Industryappointed a committee on Nonferrous Screw Fittings for the purpose of developing standardsfor products commonly designated as threaded pipe fittings of brass,bronze,or other nonferrousmaterials.At the time brass threaded fittings were furnished from a number of different patternswith wide variations in dimensions and weights.MSS SP-10 for 125 Ib Bronze Screwed Fittings and MSS SP-11 for 250 lb Bronze Screwed Fittingswere developed and adopted by the MSS in September 1930.The lighter fittings were patternedafter malleable iron threaded fittings,then standardized in ASA B16c,while the heavier productswere patterned after the cast iron threaded fittings covered by ASA B16d.Thus a practice wasstandardized that had been found satisfactory in the valve and fittings industry over many years.Following the publication of revised editions in 1941 and 1943,SP-10 was submitted to Subcom-mittee No.2 of ASA Sectional Committee B16 for adoption as an American Standard.Finalapproval of that edition was granted on January 23,1947 with the designation ASA B16.15.A reaffirmation of the Standard was granted in 1952 and a complete revision for updating theStandard was approved by ASA on March 25,1958.After revision in 1944,SP-11 was submitted to Subcommittee No.2 in August,1947 and ASAgranted the approval of B16.17 on April 6,1949.In 1961,Subcommittee No.2 reviewed the two Standards and noted that the historical reasonfor their separate existence no longer applied.Accordingly,the two were combined into ASAB16.15 with final ASA approval granted on February 6,1964.In 1969,the document was reviewed by Subcommittee No.2 and minor changes were proposed.Final ANSI approval was granted on April 14,1971.In 1977,the MSS submitted a proposed revision to Subcommittee B(formerly No.2)for B16review and approval.Changes included the addition of metric(SI)units and editorial updating.ANSI granted final approval on December 4,1978.In 1982,American National Standards Committee B16 was reorganized as the ASME B16Committee,operating under procedures accredited by ANSI.The revision,following regular5-year review by Subcommittee B,involved rationalization of metric equivalent dimensions andupdating of reference standards.Following approval within ASME,ANSI approval was grantedon July 30,1985 with the new designation ANSI/ASME B16.15-1985.In 1994,and again in 2004,the document was reaffirmed.In 2005,Subcommittee B of the ASME B16 Committee changed the title to Cast Copper AlloyThreaded Fittings,a section on leakage capacity was added,nominal size(DN)according toISO 6078 was addressed as SI values were positioned in the main text;U.S.Customary valueswere positioned in Appendix I.The reference for gaging internal fitting threads was made clearerby using the wording from ANSI/ASME B1.20.1(Pipe Threads-General Purpose-Inch).Many clarifying and editorial revisions were made in order to improve the text.After approvalby ASME,ANSI approval was granted on August 25,2006 with the new designation ofASME B16.15-2006.All requests for interpretations or suggestions for revisions should be sent to the Secretary B16,The American Society of Mechanical Engineers,Three Park Avenue,New York,N.Y.10016-5990.No roproduction or notworking permitled without liconso from IHSNot for Resale

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开