ASME_B133.9-1994.pdf

ASME 8133.9 94.0759670 0543700 262.ASME 8133.9 94.0759670 0543701 1T9.AN AMERICAN NATIONAL STANDARD Measurement of Exhaust Emissions from Stationary Gas Turbine Engines ASME 8133.9-1994(REVISION OF ANSI 8133.9-1979)The American Society of Mechanical Engineers._ _ 345 East 47th Street,New York,N.Y.10017 ASME 8133.9 94.0759670 0543702 035.Date of Issuance:June 30,1994 This Standard will be revised when the Society approves the issuance of a new edition.There will be no addenda or written interpretations of the requirements of this Standard issued to this Edition.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American National Standards.The Consensus Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate.The proposed code or standard was made available for public review and comment which provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not approve,rate,or endorse any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable Letters Patent,nor assume any such liability.Users of a code or standard are expressly advised that determination of the validity of any such patent rights,and the risk of infringement of such rights,is entirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations issued in accordance with governing ASME procedures and policies.which preclude the issuance of interpretations by individual vol-unteers.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.Copyright 1994 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All Rights Reserved Printed in U.S.A.ASME 8133.9 94.0759b70 0543703 T71.FOREWORD(This Foreword is not part of ASME 8133.9-1994.)The purpose of the B 133.9 standard is to provide criteria for the preparation of gas turbine procurement specifications.This Standard provides essential information for the procurement of gas turbine power plants.It applies to open cycle,closed cycle,and semi-closed cycle gas turbines with conventional combustion systems for industrial,ma-rine,and electric power applications.Not included are gas turbines applied to earth moving machines,agricultural and industrial-type tractors,automobiles,trucks,buses,and aero-propulsion units.The B 133.9 standard addresses exhaust emission measurements that are performed to assure compliance with federal,state,and local emission regulations.The pollutant mea-surement methods mandated by regulatory agencies are referenced and other alternative methods are outlined.Suggestions for improvement of this standard are welcome.Send suggestions to:The American Society of Mechanical Engineers,United Engineering Center,345 East 47th Street,New York,NY 10017.Approval for American National Standard B 133.9 was granted by the American Na-tional Standards Institute on April 5,1994.Ill ASME 8133.9 94.0759670 0543704 908.ASME STANDARDS COMMITTEE 8133 Procurement Standards for Gas Turbines(The following is the roster of the Committee at the time of approval of this Standard.)OFFICERS R.P.Allen.Chairman R.R.Balsbaugh,Vice Chairman A.M.Nickles,Secretary COMMITTEE PERSONNEL R.P.Allen,Clemson University R.R.Balsbaugh,Wisconsin Electric Power Co.S.M.DeCorso,Power Tech Associates,Inc.D.C.Hall,National Gas Pipeline Company of America R.A.Harmon,Consultant P.J.Hart,Allison Gas Turbine-Division of General Motors G.S.Howard,Redbrook Inc.D.B.Johnson,Tenneco Gas R.T.Lecren,Solar Turbines Inc.G.Opdyke,Consulting Engineer D.A.Rains,Decision Engineering E.Sciubba,Dept.di Mecanica Ed Aeronautica J.M.Vaught,Vaught Engineering,Inc.W.C.Walke,Jr.,Sargent&Lundy Engineers J.P.Zanyk,J.P.Zanyk and Associates,Inc.PERSONNEL OF SUBCOMMITTEE 2-FUELS AND ENVIRONMENT W.H.von Klein Smid,Chairman J.M.Vaught.Vice Chairman W.W.Bathie S.Bonifazi F.W.Crouse,Jr.S.M.DeCorso R.T.Lecren R.N.Levine J.A.McSorley C.Nakaishi G.Opdyke,Jr.P.W.Pillsbury H.Schreiber E.J.Wilson,Jr.v ASME 8133.9 94.0759670 0543705 844.PERSONNEL OF ASME STEERING COMMmEE ON DEVELOPMENT OF EMISSIONS MEASUREMENT TECHNIQUES AND SPECIFICATION FOR GAS TURBINES R.P.Allen,Clemson University R.J.Art,ASME Research W.Gray,Special Consultant,Radian Corp.W.S.Y.Hung,Solar Turbines Inc.R.Huntley,Emission Measurement Branch,USEPA J.J.Macak,Westinghouse Electric C