ASME_B16-23-2011.pdf

Cast Copper Alloy Solder Joint Drainage Fittings:DWVAN AMERICAN NATIONAL STANDARDASME B16.23-2011Revision of ASME B16.23-2002(R2006)Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-ASME B16.23-2011Revision of ASME B16.23-2002(R2006)Cast CopperAlloy SolderJoint DrainageFittings:DWVAN AMERICAN NATIONAL STANDARDThree Park Avenue New York,NY 10016 USACopyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-Date of Issuance:January 17,2012The next edition of this Standard is scheduled for publication in 2016.ASME issues written replies to inquiries concerning interpretations of technical aspects of thisStandard.Periodically certain actions of the ASME B16 Committee may be published as Cases.Cases and interpretations are published on the ASME Web site under the Committee Pages athttp:/cstools.asme.org/as they are issued,and will be published within the next edition of thestandard.Errata to codes and standards may be posted on the ASME Web site under the Committee Pages toprovide corrections to incorrectly published items,or to correct typographical or grammatical errorsin codes and standards.Such errata shall be used on the date posted.The Committee Pages can be found at http:/cstools.asme.org/.There is an option available toautomatically receive an e-mail notification when errata are posted to a particular code or standard.ThisoptioncanbefoundontheappropriateCommitteePageafterselecting“Errata”inthe“PublicationInformation”section.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American NationalStandards.The Standards Committee that approved the code or standard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participate.The proposed code or standard was madeavailable forpublic review andcomment thatprovides an opportunityfor additional publicinput from industry,academia,regulatory agencies,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with anyitems mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability forinfringement of any applicable letters patent,nor assumes any such liability.Users of a code or standard are expresslyadvised that determination of the validity of any such patent rights,and the risk of infringement of such rights,isentirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted asgovernment or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the establishedASME procedures and policies,which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright 2012 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-CONTENTSForeword.vCommittee Roster.viiCorrespondence With the B16 Committee.viiiSummary of Changes.ix1Scope.12General.13Description.14Pitch(Slope).15Abbreviations.16Size.17Marking.28Material.29Metal Thickness.210Inspection Tolerance.211Threaded Ends.212Configuration of Threaded Ends.3Figures1Typical Laying Lengths of DWV 90-deg Elbows.42Size Sequence of Fittings.4Tables1Inspection Tolerance Table.42Dimensions of Solder Joint Ends DWV.53Dimensions of Threaded Ends DWV.64Dimensions for DWV Couplings,Reducers,Extended Bushings,andFlush Bushings.75Dimensions of DWV Adapters.86Dimensions of DWV Short Adapters.97Dimensions of DWV Trap Adapters.98Dimensions of C to Soil Pipe Adapter for Joining to Extra Heavy Soil Pipe.109Dimensions of C to Soil Pipe Adapter Plain End for Joining to ExtraHeavy Soil Pipe.1110Dimensions of C?No-Hub Soil Pipe Adapter.1211Dimensions of C?Hub Soil Pipe Adapter.1312Dimensions of DWV 45-deg Y With Cleanout Soil Pipe(Spigot)?C?Cleanout.1313Dimensions of DWV Elbows and Double Elbows C?C.1414Dimensions of Reducing DWV Single and Double Elbows C?C.1515Dimensions of DWV Elbows.1616Dimensions of DWV Reducing Elbows.1717Dimensions of DWV