ASME_B107.4M-1995.pdf

INDD B107.48225955120077972564ANSI-B107.4ADOPTION NOTICEANSI-B107.4,Tools,Electric,Portable Hand,Air,Drivingand Spindle Ends For,was adopted on October 3,1994 foruse by the Department of Defense(DOD).Proposed changes byDoD activities must be submitted to the DoD AdoptingActivity:Commander,US Army Natick Research,Developmentand Engineering Center,ATTN:SATNC-AEL,Natick,MA 01760-5000.DoD activities may cbtain copies of this standardfrom the standardization Document Order Desk,700 RobbinsAvenue,Building 4D,Philadelphia,PA 19111-5094.Theprivate sector and other Government agencies may purchasecopies from the American National Standards Institute,11West 42nd street,New York,NY 10035.Custodians:Adopting ActivityArmy-GLArmy GLNavy-ASAir Force 94FSC 5130DISTRIBUTION STATEMENT A.Approved for public release;distribution is unlimited.Copyright by the American Society Of Mechanical EngineersASME B107.4M950759b700572262802ASME B107.4M-1995(BEVISION OF ANSI B107 4-1982)Driving and Spindle Endsfor Portable Hand,Impact,Air,and Electric Tools(Percussion Tools Excluded)AN AMERICAN NATIONAL STANDARDThe american society ofMechanical EngineersASME B107.4M95=0759b700572263749AN AMERICAN NATIONAL STANDARDDriving and Spindle Endsfor Portable Hand,Impact,Air,and Electric Tools(Percussion Tools Excluded)ASME B107.4M-1995(REVISION OF ANSI B107.4-1982)(AThe American Society ofMechanical Engineers345 East 47th Street,New York,N.Y.10017ASME B107.4M95=0759b700572264685Datc of Issuance:December 15,1995This Standard will be revised when the Society approves the issuance ofa new edition.There will be no addenda or written interpretations of therequirements of this Standard issued to this edition.ASME is the registered trademark of the American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria forAmerican National Standards.The Consensus committee that approved the code or standardwas balanced to assure that individuals from competent and concerned interests have had anopportunity to participate.The proposed code or standard was made available for public reviewand comment which provides an opportunity for additional public input from industry,academia.regulatory agencies,and the public-at-large.ASME does not approve,rate,or endorseany item,construction,proprietary deviceor activity.ASME does not take any pusition with respect to the vaiidity of any patent rights asserted inconnection with any items mentioned in this documont,and does not undertake to insure anyoneutilizing a standard against liability for infringement of any applicable I etters Patent,nor assumeany such liability.Users of a code or standard are expressiy advised that determination of thevalidity of any such patent rights,and the risk of infringement of such rights,is entirely theirown responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not tobe interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations issued in accordance with governingASME procedures and policies which preciude the issuance of interpretations by individualvolunteers.No part of this document may be reproduced in any form,in an electronic retrieval system or otierwise,without the prior written permission of the publisher.Copyright 1995 byTHE AMERICAN SOCIEIY OF MECHANICAL ENGINEERSAll Rights ReservedPrinted in U.S.A.ASME B107.4M95=0759b700572265511FOREWORD(This Foreword is not part of ASME B107.4M-1995.)The American National Standards Committee B107,Socket Wrenches and Drives,undersponsorship by the American Society of Mechanical Engineers,held its organizational meetingon June 28,1967.Subcommittee 1 on Driving Ends for Portable Hand,Air,and Electric Toolsand Subcommittee 3 on Spindle Ends for Portable Air and Electric Tools were subsequentlyorganized.These two subcommittees took over the work that was originally handled by TechnicalCommittee 28 of Standards Committee B5.The data contained in this Standard supersedes thatin the B107.4 1982(R1988)document.Suggestions for improvement of this Standard will be welcome.They should be sent to TheAmerican Society of Mechanical Engineers,Attn:Secretary,B107 Main Committee,345 East47th Street,New York,NY 10017.This revision was approved as an American National Standard on October 16,1905.i