ASME_B107-17-1997.pdf

STDSASME B107-L7M-ENGL 1997 U 0759b70 Ob07093 LT7 Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-A N 3 The imerican Society of I Mechanical Engineers A M E R I C A N N A T I O N A L S T A N D A R D EAGES,WRENCH OPENINGS,REFERENCE ASME B107.17M-1117 REViSiOII 01 ANWASME B107.17M-lfl85(R1 flfll)Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-Date of Issuance:December 31,1998 This Standard will be revised when the Society approves the issuance of a new edition.There will be no addenda or written interpretations of the requirements of this Standard issued to this edition.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American National Standards.The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate.The proposed code or standard was made available for public re-view and comment which provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not approve,rate,or endorse any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document,and does not undertake to insure any-one utilizing a standard against liability for infringement of any applicable Letters Patent,nor assumes any such liability.Users of a code or standard are expressly advised that determina-tion of the validity of any such patent rights,and the risk of infringement of such rights,is en-tirely their own responsibility.Participation by federal agency representative(s1 or personb)affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations issued in accordance with gov-erning ASME procedures and policies which preclude the issuance of interpretations by indi-vidual volunteers.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical Engineers Three Park Avenue,New York,NY 10016-5990 Copyright(Q 1999 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All Rights Reserved Printed in U.S.A.Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-FOREWORD(This Foreword is not part of ASME 8107.17M-1997.)The American National Standards Committee B107,Sockets Wrenches and Drives,under sponsorship by the American Society of Mechanical Engineers,held its organizational meeting on June 28,1967.Subsequently,the Committee was reorganized as an ASME Standards Committee and its title was changed to Hand Tools and Accessories.During 1994,1995,and 1996 the B107 Committee reviewed the“Go”and“No Go”gage sizes and agreed on changes to certain sizes.After Standards Committee and ASME approval,and public review,this ASME B 107.17M-1997,Gages,Wrench Openings,Reference,was approved as an American National Standard by ANSI on February 6,1997.This is a reprint of B107.17M-1997 with revisions.111 Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-ASME STANDARDS COMMITTEE B107 Hand Tools and Accessories(The following is the roster of the Committee at the time of approval of this Standard.)OFFICERS R.R.McCullough,Chair R.B.Wright,Vice Chair G.L.Fechter,Secretary COMMITTEE PERSONNEL R.M.Byrne,Trade Association Management,Inc.A.A.Speranza,Alternate,Hand Tools Institute A.Carr,Federal Supply Service R.P.Hall,US Air Force A.Herskovitz,US Department of the Army S.Jiles,Southern California Gas C.M.Knapp,AFMC-CASC/LGHB J.C.Marvil,General Services Administration R.R.McCullough,Chair,Cooper Industries G.E.Olson,Gene Olson Engineering Consultant B.Pagac,Snap-On Inc.R.W.Reynolds,Stanley Mechanics Tools W.R.Wacker,BAC Associates,Inc.R.B.Wright,Vice Chair,Wright Tool Co.V Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-CONTENTS.Foreword.111 Standards Committee Roster.v 1 Scope.1 2 Application.1 3 Normative References.1 4 Requirements.1 Figures 1 Hex Gage Dimensions.2 2 Square Gage Dimensions.3 Tables 1A Hexagon or Square(Inch Series).4 1B Incremental Amount(Inch Series).5 2A Hexagon or Square(Metric Series.6 2B Incremental Amount(Metric Series).7 3A Spark Plug Hexagon.8 vii Copyright ASME International Provided by IHS under li