ASME_B107
2002
Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-The American Society of Mechanical Engineers A N AMERICAN NATIONAL STANDARD SOCKET WRENCHES HAND(INCH SERIES!ASIE B107.1-2002(Revision al ASME B107.1-1flH3)Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-Date of Issuance:March 31,2003 This Standard will be revised when the Society approves the issuance of a new edition.There will be no addenda issued to this edition.ASME issues written replies to inquiries concerning interpretations of technical aspects of this Standard.Interpretations are published on the ASME Web site under the Committee Pages at http:/www.asme.org/codes/as they are issued.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American National Standards.The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate.The proposed code or standard was made available for public review and comment that provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not approve,rate,or endorse any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document,and does not undertake to insure anyone utilizing a standard against liabilityfor infringement of any applicable letters patent,nor assumes any such liability.Users of a code or standard are expressly advised that determination of the validity of any such patent rights,and the risk of infringement of such rights,is entirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures and policies,which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical Engineers Three Park Avenue,New York,NY 10016-5990 Copyright O 2003 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All Rights Reserved Printed in U.S.A.Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-CONTENTS Foreword.iv Committee Roster.v Correspondence With the B 107 Committee.vi 1 Scope.1 2 Classification.1 3 Normative References.1 4 Requirements.1 5 Test Procedures.3 6 Designations.4 7 Safety Requirements and Limitations of Use.4 Figures 1 Type I and II Sockets,Class 1,Regular Length;Class 2,Long Length;Class 3,Mid Length.5 2 Type III,Universal Sockets,Block Type.6 1 Type I Classes 1,2,and 3 Socket,Single and Double Hexagon,Regular,2 Type I Classes 1,2,and 3 Socket,Single and Double Hexagon,Regular,3 Type I Classes 1,2,and 3 Socket,Single and Double Hexagon,Regular,4 Type I Classes 1 and 2 Socket,Single and Double Hexagon,Regular and 5 Type I Class 1 Socket,Single and Double Hexagon,Regular Length,1 in.Tables Long,and Mid Length,14 in.Drive.7 Long,and Mid Length,3/in.Drive.7 Long,and Mid Length,12 in.Drive.8 9 Drive.10 7 11 8 11 9 Type III Socket,Universal,Single and Double Hexagon,in.Drive.12 12 12 13 15 Long Length,3/4 in.Drive.6 Type II Socket,Square,4-and 8-Point,in Drive.11.Type II Socket,Square,4-and 8-Point,3/s in.Drive.Type II Socket,Square,4-and 8-Point,12 in.Drive.10 Type III Socket,Universal,Single and Double Hexagon,3/8 in.Drive.11 Type III Socket,Universal,Single and Double Hexagon,/2 in.Drive.12 13 Square Mandrel Dimensions and Maximum Depth of Mandrel Insertion.Hexagon Mandrel Dimensions and Maximum Depth of Mandrel Insertion.111 Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-FOREWORD The American National Standards Committee B 107,Socket Wrenches and Drives,under sponsorship of The American Society of Mechanical Engineers(ASME),was reorganized as an ASME Standards Committee,and its title was changed to Hand Tools and Accessories.The purpose of this Standard is to define general and dimensional data specifically applicable to detachable socket wrenches and to specify test methods to evaluate performance relating to the defined requirements.This Standard is a revision of B107.1-1993 Socket Wrenches,Hand(Inch Series).A principal change in this edi