ASME_B107.410-2018.pdf

AN AM E R IC AN NAT IO NAL STANDARDASME B107.410-2018(Revision of ASME B107.410-2008)Struck ToolsASME B107.410-2018(Revision of ASME B107.410-2008)Struck ToolsAN AMERICAN NATIONAL STANDARDxDate of Issuance:January 25,2019This Standard will be revised when the Society approves the issuance of a new edition.ASME issues written replies to inquiries concerning interpretations of technical aspects of this Standard.Interpretations arepublishedontheCommitteewebpageandunderhttp:/go.asme.org/InterpsDatabase.PeriodicallycertainactionsoftheASMEB107 Committee may be published as Cases.Cases are published on the ASME website under the B107 Committee Page athttp:/go.asme.org/B107committee as they are issued.Errata to codes and standards may be posted on the ASME website under the Committee Pages to provide corrections toincorrectlypublisheditems,ortocorrecttypographicalorgrammaticalerrorsincodesandstandards.Sucherratashallbeusedon the date posted.The B107 Committee Page can be found at http:/go.asme.org/B107committee.There is an option available to automaticallyreceive an e-mail notification when errata are posted to a particular code or standard.This option can be found on theappropriate Committee Page after selecting“Errata”in the“Publication Information”section.ASME is the registered trademark of The American Society of Mechanical Engineers.ThiscodeorstandardwasdevelopedunderproceduresaccreditedasmeetingthecriteriaforAmericanNationalStandards.TheStandardsCommitteethatapprovedthecodeorstandardwasbalancedtoassurethatindividualsfromcompetentandconcernedinterestshavehadanopportunityto participate.The proposed codeorstandardwasmadeavailable forpublic reviewandcommentthatprovidesanopportunityfor additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in thisdocument,anddoesnotundertaketoinsureanyoneutilizingastandardagainstliabilityforinfringementofanyapplicableletterspatent,norassumeanysuchliability.Usersofacodeorstandardareexpresslyadvisedthatdeterminationofthevalidityofanysuchpatentrights,andtherisk of infringement of such rights,is entirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted as government or industryendorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME proceduresand policies,which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersTwo Park Avenue,New York,NY 10016-5990Copyright 2019 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.CONTENTSForeword.vCommittee Roster.viCorrespondence With the B107 Committee.vii1Scope.12Definitions.13References.64Classification.65Performance Requirements.66Tests.257Safety Requirements and Limitations of Use.41Figures5.1-1Category 43 Wood-Splitting Wedges.95.1-2Category 43 Square Head Wedges.95.1-3Category 43 Stave and Oregon-Splitting Wedges.95.2-1Category 44 Glaziers Chisels.105.2-2Category 44 All-Steel Wood Chisels.105.2-3Category 44 Wood Chisels.115.2-4Category 44 Ripping Chisels.125.2-5Category 44 Flooring/Electricians Chisels.135.3-1Category 46 Multi-Spline Extractor.145.3-2Category 46 Spiral Flute Extractor.145.3-3Category 46 Straight Flute Extractor.155.3-4Category 46 Tapered Flute Extractor.155.4.1-1Category 48 Type I Chisels.165.4.1-2Category 48 Type I Handle-Held Chisels.165.4.2-1Category 48 Type II Punches.175.4.2-2Category 48 Type II Handle-Held Punches.185.4.3-1Category 48 Type III Drift Pins.185.5.1-1Category 49 Type I Nail Set.195.5.2-1Category 49 Type II(Self-Centering)Nail Set.195.6-1Category 50 Brick Chisel and Brick Set.205.6-2Configuration of Category 50 Brick Chisel and Brick Set Bevels.205.6-3Category 50 Star Drill.215.7.1-1Category 52 Type I Struck Nail-Puller Bars.225.7.1-2Category 52 Type II,Class 1 Nonstruck Multipurpose Bar.235.7.1-3Category 52 Type II,Class 2 Nonstruck Ripping/Wrecking Bar.235.7.2-1Category 52 Type III,Class 1 Close Quarter Pry Bar.23iii5.7.3-1Category 52 Type III,Class 2 Die Setter Pry Bar.235.7.4-1Category 52 Type III,Class 3 Handled Pry Bar.235.7.5-1Category 52 Type III,Class 4 Pinch Bar.235.7.6-1Category 52 Type III,Class 5 Rolling Head Pry Bar.245.8-1Category 59 Striking Wrenches.245.8-2Category 59 Slugging Wrenches.245.8-3Struck Block Cross Section.246.2.2-1Impact Test for Category 44 Types I and II Chisels.306.2.8-1Category 52 Handle Impact Test.336.2.9.1-1Impact Test Setup.346.4-1Category 44 Side Force Test.356.5.1-1Category 44 Permanent Set Test