分享
ASME_B107.15-2002.pdf
下载文档

ID:166981

大小:553.81KB

页数:14页

格式:PDF

时间:2023-03-03

收藏 分享赚钱
温馨提示:
1. 部分包含数学公式或PPT动画的文件,查看预览时可能会显示错乱或异常,文件下载后无此问题,请放心下载。
2. 本文档由用户上传,版权归属用户,汇文网负责整理代发布。如果您对本文档版权有争议请及时联系客服。
3. 下载前请仔细阅读文档内容,确认文档内容符合您的需求后进行下载,若出现内容与标题不符可向本站投诉处理。
4. 下载文档时可能由于网络波动等原因无法下载或下载错误,付费完成后未能成功下载的用户请联系客服处理。
网站客服:3074922707
ASME_B107 15 2002
Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-The American Society of Mechanical Engineers AMERICAN NATIONAL STANDARD FLAT TIP SCREWDRIVERS ASME B107.15-2002(R e v i s i o n of ASME B107.1!-i!)Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-Date of issuance:January 15,2003 This Standard will be revised when the Society approves the issuance of a new edition.There will be no addenda issued to this edition.ASME issues written replies to inquiries concerning interpretations of technical aspects of this Standard.Interpretations are published on the ASME Web site under the Committee Pages at http:/www.asme.org/codes/as they are issued.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American National Standards.The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate.The proposed code or standard was made available for public review and comment that provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not approve,rate,or endorse any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document,and does not undertake to insure anyone utilizing a standard against liabilityfor infringement of any applicable letters patent,nor assume any such liability.Users of a code or standard are expressly advised that determination of the validity of any such patent rights,and the risk of infringement of such rights,is entirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures and policies,which precludes the issuance of interpretations by individuais.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical Engineers Three Park Avenue,New York,NY 10016-5990 Copyright O 2003 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All rights reserved Printed in U.S.A.Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-CONTENTS Foreword.iv Standards Committee Roster.v Correspondence With the B107 Committee.vi 1 Scope.1 2 Classification.1 3 Normative References.1 4 Definitions(See Fig.1).1 5 Requirements.2 6 Test Procedures.3 7 Designations.6 Figures 1 Descriptions.1 2 Typical Appearances.2 3 Fiat Tip Screwdriver Nomenclature at t1.2 4 Typical Appearance of a Cushion Grip Screwdriver.3 4 5B Cross Section of Slot for Typical Torsional Test Block.5 6 Bending Moment Test.Typical Setup.6 Tables 1 Dimensional Characteristics of Flat Tip Screwdrivers.3 2 Performance Characteristics of Flat Tip Screwdrivers.4 3 impact Test Data.5 5A Typical Torsional Test Block.iii Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-FOREWORD The American National Standards Committee B107,Socket Wrenches and Drives,under sponsorship of The American Society of Mechanical Engineers,was reorganized as an ASME Standards Committee,and its title was changed to Hand Tools and Accessories.In 1996 its scope was expanded to address safety considerations.The purposes of this Standard are to define general and dimensional data and safety considerations specifically applicable to flat tip screwdrivers and to specify test methods to evaluate performance relating to the defined requirements.This Standard is a revision of ASME B107.15-1993 Flat Tip and Phillips Screwdrivers.Principal changes in this Standard are the exclusion of Phillips screwdrivers(which can now be found in ASME B107.30-2002 Cross Tip Screwdrivers)and the addition of safety considerations.The format of this Standard is in accordance with The ASME Codes and Standards Writing Guide 2000.Requests for interpretations of the technical requirements of this Standard should be expressed in writing to the Secretary,B107 Committee,at the address below.Suggestions for the improvement of this Standard are welcome.They should be addressed to The American Society of Mechanical Engineers,Secretary,B107 Standards Committee,Three Park Avenue,New York,NY 10016-5990.The requirements of

此文档下载收益归作者所有

下载文档
你可能关注的文档
收起
展开