ASME_B1.10M-1997.pdf

STD.ASME B1.10M-ENGL19970759b7005888923B7ErratatoASME B1.10M-1997Unified Miniature Screw ThreadsOn page 6,in Table 2.under the fifth column heading Height,0.661F=0.57259074P,theeighth and ninth entries were corrected to read 0.12883 and 0.14315,respectively.The completeTable appears on the overleaf.THE AMERICAN SOCIETY OF MECHANICAL ENGINEERSJANUARY 1998345 East 47th Street,New York,NY 10017N2597ECOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesSTD.ASMEB1.10M-ENGL19970075967015B8B93213e snipey8391100020000爱含11000000810.022002110028200夏B80084900pepunoy=H9690621100855001S760.0772950279200esnipe09781386041002000610022008200Z000880P.P000011610010080100421008800061200152008180034610H7931)1.087610082200m0856002200107555507893104-8600ruex3 jo=HSLEO8692002262008140006107088930081180027600pue0.0000101377790001307000000300709000Jo 34BIOH82690516170.084000076520.0129453899200800121015101120080COPYRIGHTAmerican Society of Mechanical EngineersLicensed by Information Handling ServicesSTD.ASME BL.10M-ENGL 199707596700583028678ASME B1.10M-1997UNIFIED MINIATURESCREW-THRE歌DS(Revision of ASA B1.10-1958)ANA MERICANNALLONA L STAN DARDThe American Society ofMechanical Engineerse0PR近HT AnecianSoeCyMechania见n90oe3Licensed by Intormation Handling ServicesSTD.ASME B1.10M-ENGL19970759b700583029504The American Society ofMechanical EngineersAN AMERICANNAT ION AL ST A N D A R DUNIFEDMINIATURESCREW THREADSASME B1.10M-1997(Revision of ASA B1.10-1958)COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesSTD.ASME B1.10M-EN6L19970759b700583030226Date of Issuance:September 2,1997This Standard will be revised when the Society approves the issuance ofa new edition.There will be no addenda or written interpretations of therequirements of this Standard issued to this edition.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria forAmerican National Standards.The Consensus Committee that approved the code or standardwas balanced to assure that individuals from competent and concerned interests have had anopportunity to participate.The proposed code or standard was made available for public reviewand comment which provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not approve,rate,or endorseany item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted inconnection with any items mentioned in this document,and does not undertake to insure anyoneutilizing a standard against liability for infringement of any applicable Letters Patent,nor assumeany such liability.Users of a code or standard are expressly advised that the determination ofthe validity of any such patent rights,and the risk of the infringement of such rights,is entirelytheir own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not tobe interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations issued in accordance with governingASME procedures and policies which preclude the issuance of interpretations by individualvolunteers.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical Engineers345 East 47th Street,New York,NY 10017Copyright1997byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll Rights ReservedPrinted in U.S.A.COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services