ASME_B107.22M-1998.pdf

ASME B107.22M1998(Revision of ASME B107.22M-1991)ELECTRONICCUTTERSAN AMERICAN NATIONAL STANDARDREAFFIRMED 2004FOR CURRENT COMMITTEE PERSONNELPLEASE E-MAIL CSasme.orgThe American Society ofMechanical Engineerse with ASMENo or networking permitted without lcense from SNot for ResaleThe American Society ofMechanical EngineersAN AMERICAN NATIO N AL ST AN D A R DELECTRONICCUTTERSASME B107.22M-1998(Revision of ASME B107.22M-1991)rAOMENo reproduction or networking permitted without license from IHSNot for ResaleDate of issuance:October 30.1998This Standard will be revised when the Society approves the issuance ofa new edition.There will be no addenda or written interpretations of therequirements of this Standard issued to this edition.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria forAmerican National Standards.The Standards Committee that approved the code or standardwas balanced to assure that individuals from competent and concerned interests have had anopportunity to participate.The proposed code or standard was made available for public reviewand comment,which provides an opportunity for additional public input from industry,academia.regulatory agencies,and the public-at-large.ASME does not approve,rate,or endorseany item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights.asserted inconnection with any items mentioned in this document,and does not undertake to insure anyoneutilizing a standard against liability for infringement of any applicable Letters Patent,nor assumesany such liability.Users of a code or standard are expressly advised that determination of thevalidity of any such patent rights,and the risk of infringement of such rights,is entirely theirown responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not tobe interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations issued in accordance with governingASME procedures and policies which precludes the issuance of interpretations by individualvolunteers.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright 1998 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll Rights ReservedPrinted in U.S.A.Copyrigh ASME IntemaonalFOREWORD(This Foreword is not part of ASME B107.22M-1998.)The American National Standards Committee B107,Socket Wrenches and Drives,undersponsorship of the American Society of Mechanical Engineers,held its organizational meetingon June 28,1967.Subsequently,the Committee was recognized as an ASME StandardsCommittee and was changed to Hand Tools and Accessories.Members of the Hand Tools Institute Plier Standards Committee have been majorcontributors to the development of this Standard in their committee work,their knowledgeof the product.and their active efforts in promoting the adoption of the standard.This Standard on Electronic Cutters is the first standard covering the dimensional andfunctional characteristics of this type of pliers used in the electronic industry.Followingthe approval by the Standards Committee B107 and ASME.this Standard was approvedby the American National Standards Institute on July 16,1998.甜o with ASMENo roproduction or networking pormtod without liconso from IHSNot for RosaleASME STANDARDS COMMITTEE B107Hand Tools and Accessories(The following is the roster of the Committee at the time of approval of this Standard.)OFFICERSR.R.McCullough,ChairR.B.Wright,Vice ChairJ.R.Bird,SecretaryCOMMITTEE PERSONNELR.M.Byrne,Trade Association Management,IncA.A.Speranza,Alternate,Hand Tools InstituteJ.R.Bird.The American Society of Mechanical EngineersA.Herskovitz,U.S.ArmyH.Kimball,Naval Air Warfare CenterC.M.Knapp,CASC/LGHBR.R.McCullough,Cooper IndustriesJ.C.Marvil,General Services AdministrationA.Carr,Alternate,Federal Supply ServiceG.E.Olson,Gene Olson Engineering Consultants,Ltd.W.T.Pagac,Snap-On Tools,Inc.R.W.Reynolds,Stanley Mechanics Tools,Inc.W.R.Wacker,BAC Associates,Inc.R.B.Wright,Wright Tool Co.Copyright ASME IntemasionalProvided by IHS under license with ASMENo reproduction or networking permitted without license from IHSNot for Resale