19-8_Addn-b_2009.pdf

ASME A112.19.8b-2009Addenda toASME A112.19.8-2007Suction Fittings for Use inSwimming Pools,Wading Pools,Spas,and Hot TubsAN AMERICAN NATIONAL STANDARDJ0118BCopyright 2010 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.Date of Issuance:March 1,2010ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American NationalStandards.The Standards Committee that approved the code or standard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participate.The proposed code or standard was madeavailable forpublic review andcomment thatprovides an opportunityfor additional publicinput from industry,academia,regulatory agencies,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with anyitems mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability forinfringement of any applicable letters patent,nor assumes any such liability.Users of a code or standard are expresslyadvised that determination of the validity of any such patent rights,and the risk of infringement of such rights,isentirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted asgovernment or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the establishedASME procedures and policies,which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright 2010 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.Copyright 2010 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ASME A112.19.8b-2009Following approval by the ASME A112 Committee and ASME,and after public review,ASME A112.19.8b-2009 was approved by the American National Standards Institute onOctober 22,2009.Addenda to the 2007 edition of ASME A112.19.8 are issued in the form of replacement pages.Revisions,additions,anddeletionsareincorporateddirectlyintotheaffectedpages.Itisadvisable,however,that this page,the Addenda title and coyright pages,and all replaced pages be retainedfor reference.SUMMARY OF CHANGESThis is the second Addenda to be published to ASME A112.19.8-2007.The first Addenda waspublished in 2008.Replace or insert the pages listed.Changes given below are identified on the pages by a marginnote,(b),placed next to the affected area.Previous Addenda changes are indicated by(a).Thepages not listed are the reverse sides of the listed pages and contain no changes.PageLocationChange16.11.1.6.6Added1.1.7.1The word“Drain”has been revised toread“Outlet”in three places1.4Listing for IAPMO standard referenceadded1.5(1)Definition for anti-vortex and dualoutlets revised(2)Definition for body membrane,dual blockage,and single blockagedeleted(3)Definition for self-contained factorymanufactured spa and self-contained spafittings added2.3.5Added3.1.1Revised8.14.1.2.2Revised914.14.1.5.7Second and third sentences revised4.2.2.1AddedFig.6aAddedFig.8Revised5.1.2.1.1Added5.2.1.1Revised5.2.1.2Revised(c)Copyright 2010 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.177.1.1Revised in its entirety7.1.2Paragraph reference updated7.2.1(a)(3)Revised20Table II-1Revised(d)Copyright 2010 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ASME A112.19.8b-2009SUC