AG-1_Addn-b_2008.pdf

AN AMERICAN NATIONAL STANDARDASME AG-1b2007ADDENDAtoASME AG-12003CODE ON NUCLEAR AIR AND GAS TREATMENTTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSThree Park AvenueTNew York,NY 10016A01222hiili1$#11Copyright 2008 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.Date of Issuance:June 20,2008ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American NationalStandards.The Standards Committee that approved the code or standard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participate.The proposed code or standard was madeavailable for public review and comment that provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with anyitems mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability forinfringement of any applicable letters patent,nor assumes any such liability.Users of a code or standard are expresslyadvised that determination of the validity of any such patent rights,and the risk of infringement of such rights,is entirelytheir own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted asgovernment or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the establishedASME procedures and policies,which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright 2008 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.hiili1$#29996Copyright 2008 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ASME AG-1b2007Following approval by the ASME Committee on Nuclear Air and Gas Treatment(CONAGT),and afterpublic review,ASME AG-1b2007 was approved by the American National Standards Institute on October11,2007.Addenda to the ASME AG-1-2003 are issued in the form of replacement pages.Revisions,additions,anddeletions are incorporated directly into the affected pages.It is advisable,however,that this page,theAddenda title and copyright pages,and all replaced pages be retained for reference.SUMMARY OF CHANGESThis is the second Addenda to be published to ASME AG-1-2003.A previous Addenda was published onSeptember 30,2005.Replace or insert the pages listed.Changes given below are identified on the pages by a margin note,(b),placed next to the affected area.Changes made in ASME AG-1-2003 are indicated by(03).Previousaddenda changes are indicated by(a).The pages not listed are the reverse sides of the listed pages andcontain no changes.PageLocationChangeiii,ivContentsUpdated to reflect AddendavForewordRevised in its entirety3Section AA ContentsUpdated17Table AA-4323Note(1)revisedAA-4332.1RevisedAA-4332.2First sentence revisedAA-4332.3(a)Revised24AA-4360Revised27AA-5130RevisedAA-5221Third sentence revised28AA-5700Note deleted31AA-6310(i)Revised34AA-6335.1RevisedAA-6410(i)Revised35AA-6433.1Revised37AA-6534Revised38AA-6610(a)Second sentence revised(c)hiili1$07#3ddCopyright 2008 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.PageLocationChange39,40AA-7200Third and fourth paragraphs revisedAA-7220RevisedAA-7230Second paragraph revisedAA-7310Second paragraph revised43.143.3Article AA-10000Added235Article RA-2000References updated236RA-3100(d)AddedRA-3110(1)Subparagraph(c)revised(2)In last paragraph,spelling of the word“manufacturers”corrected by errataRA-3120(b)Revised237RA-3151RevisedRA-3152(b)RevisedRA-3153RevisedRA-3154RevisedRA-3160(c)RevisedRA-3160(d)Revised238