ASME_A112.6.2-2000.pdf

STD.ASME A112.b.2-EN6L200007596700b20900405=ASME A112.6.22000E0酬FRAMING AFFIXEDSUPPORTS FORFT班H0RWMRCLOSETS WITHCONCEALED TANKSAN AMERICAN NATIONAL STANDARDEThe American Society ofMechanical EngineersCopyright by the American Society Of Mechanical EngineersSTD.ASME A112.6.2-ENGL20000759b700620901341The American Society ofMechanical EngineersA N A ME R IC AN NA T I ON A L ST A N D A R DFRAMING-AFFIXEDSUPPORTS FOROFF-THE-FLOOR WATCLOSETS WITEETAStA112.6.2-2000ESTD.ASME A112.62-EN6L20000759670062090228BDate of Issuance:December 29,2000This Standard will be revised when the Society approves the issuancc ofa new edition.There will be no addenda or written interprctations of thcrequirements of this Standard issued to this edition.ASME is the registered trademark of The American Society of Mechanical EngineersThis code or standard was developed under procedures accredited as meeting the criteria forAmerican National Standards.The Standards Committee that approved the code or standardwas halanced to assure that individuals from competent and concerned interests have had anopportunity to participate.The proposed code or standard was made available for public reviewand comment that provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not approve,rate,or endorseany item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted inconnection with any items mentioned in this document,and does not undertake to insure anyoneutilizing a standard against liability for infringement of any applicable letters patent,nor assumeany such liability.Users of a code or standard are expressly advised that determination of thevalidity of any such patent rights,and the risk of infringement of such rights,is entirely theirown responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not tohe interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued inaccordance with the cstablished ASME procedures and policies,which precludes the issuanceof interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisherThe American Society of Mechanical EngineersThree Park Avenuc,New York,NY 10016-5990Copyright 2000 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll Rights ReservedPrinted in U.S ASTD.ASME A112.6.2-ENGL20000759b700620903114FOREWORDIn 1990.the American Society of Mechanical Engineers was solicited to develop astandard for carriers that are used in frame construction.At the time,a standard existedfor the evaluation of carriers for floor-affixed carriers and supports that are typically installedin commercial,indusuial,and institutionai buildings with concrete floors.The standard forfloor-supported carriers and suppoits is ASME A112.6.IM.This Standard complements ASME A112.6.1M.Some of the specifications and tests aresimilar and appropriately.are referenced in this Standard.However.due to differences inassembly of thesc framing-affixed products from the floor-affixed products,some criteriaare different.The basis for this Standard was an Intcrim Guide Criteria document prepared by theInternational Association of Plumbing and Mechanical Officials(IAPMO).Suggestions for improvement of this Standard are welcome.They should be sent to TheAmerican Society of Mechanical Engineers;Attn:Secretary.Al12 Main Committee:ThreePark Avenue:New York.NY 10016.This Fdition was approved as an American National Standard on October 18.2000.拥