ASME_A112.18.2-2005.pdf

ASME A112.18.2-2005/CSAB125.2-05Plumbing waste fittingsThe American Society ofCANADIAN STANDARDSMechanical EngineersASSOCIATIONNo roproduction or notworking permitled without liconso from IHSNot for RosaleLegal Notice for Harmonized StandardJointly Developed by ASME and CSAIntellectual property rights and ownershipAs between American Society of Mechanical Engineers(ASME)and Canadian Standards Association(CSA)(collectively ASMEand CSA)and the users of this document(whether it be in printed or electronic form),ASME and CSA are the joint owners of allworks contained herein that are protected by copyright,all trade-marks(except as otherwise noted to the contrary),and allinventions and trade secrets that may be contained in this document,whether or not such inventions and trade secrets areprotected by patents and applications for patents.The unauthorized use,modification,copying,or disclosure of this documentmay violate laws that protect the intellectual property of ASME and CSA and may give rise to a right in ASME and CSA to seeklegal redress for such use,modification,copying,or disclosure.ASME and CSA reserve all intellectual property rights in thisdocument.Disclaimer and exclusion of liabilityThis document is provided without any representations,warranties,or conditions of any kind,express or implied,includingwithout limitation,implied warranties or conditions concerning this documents fitness for a particular purpose or use,itsmerchantability,or its non-infringement of any third partys intellectual property rights.ASME and CSA do not warrant theaccuracy,completeness,or currency of any of the information published in this document.ASME and CSA make norepresentations or warranties regarding this documents compliance with any applicable statute,rule,or regulation.IN NO EVENT SHALL ASME AND CSA,THEIR RESPECTIVE VOLUNTEERS,MEMBERS,SUBSIDIARIES,OR AFFILIATED COMPANIES,OR THEIR EMPLOYEES,DIRECTORS,OR OFFICERS,BE LIABLE FOR ANY DIRECT,INDIRECT,OR INCIDENTAL DAMAGES,INJURYLOSS,COSTS,OR EXPENSES,HOWSOEVER CAUSED,INCLUDING BUT NOT LIMITED TO SPECIAL OR CONSEQUENTIALDAMAGES,LOST REVENUE,BUSINESS INTERRUPTION,LOST OR DAMAGED DATA,OR ANY OTHER COMMERCIAL ORECONOMIC LOSS,WHETHER BASED IN CONTRACT,TORT(INCLUDING NEGLIGENCE),OR ANY OTHER THEORY OF LIABILITYARISING OUT OF OR RESULTING FROM ACCESS TO OR POSSESSION OR USE OF THIS DOCUMENT,EVEN IF ASME OR CSA HAVEBEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES,INJURY,LOSS,COSTS,OR EXPENSES.In publishing and making this document available,ASME and CSA are not undertaking to render professional or other services foror on behalf of any person or entity or to perform any duty owed by any person or entity to another person or entity.Theinformation in this document is directed to those who have the appropriate degree of experience to use and apply its contents,and ASME and CSA accept no responsibility whatsoever arising in any way from any and all use of or reliance on the informationcontained in this document.ASME and CSA have no power,nor do they undertake,to enforce compliance with the contents of the standards or otherdocuments they jointly publish.Authorized use of this documentThis document is being provided by ASME and CSA for informational and non-commercial use only.The user of this document isauthorized to do only the following:If this document is in electronic form:load this document onto a computer for the sole purpose of reviewing it;search and browse this document;andprint this document.Limited copies of this document in print or paper form may be distributed only to persons who are authorized by ASME and CSAto have such copies,and only if this Legal Notice appears on each such copy.In addition,users may not and may not permit others toalter this document in any way or remove this Legal Notice from the attached standard;sell this document without authorization from ASME and CSA;ormake an electronic copy of this document.If you do not agree with any of the terms and conditions contained in this Legal Notice,you may not load or use this documentor make any copies of the contents hereof,and if you do make such copies,you are required to destroy them immediately.Use ofthis document constitutes your acceptance of the terms and conditions of this Legal Notice.城The American Society ofCANADIAN STANDARDSMechanical EngineersASSOCIATION。whAg/ENo roproduction or natworking permitled without liconso from IHSNot for RosaleCSA Standards Update ServiceASME A112.18.2-2005/CSAB125.2-05June 2005Title:Plumbing waste fittingsPagination:37 pages(xiv preliminary and 23 text),each dated June 2005Automatic notifications about any updates to this publication are available.To register for e-mail notifications,and/or to download any existing updates in PDF,enterthe Online Store at www.ShopCSA.ca and click on My Account on the navigation bar.The List ID for this document is 2016523.To receive printed updates,please complete and return the attached card.NameOrganizationAddressCityProvince/StateCountryPostal/Zip CodeE-mailI consent to CSA collecting and using the above information to send me updates relating to this publication.Visit CSAs policy on privacy at www.csagroup.org/legal to find out how we protect your personal information.ASME A112.18.2-2005/CSAB125.2-05whAgNo roproduction or notworking permitled without liconso from IHSNot for RosaleASME/CSA StandardASME A112.18.2-2005CSAB125.2-05Plumbing waste fittings02The American Society ofMechanical EngineersCANADIAN STANDARDSASSOCIATIONRegistered trade-mark of Canadian Standards AssociationNo roproduction or notworking permitled without liconso from IHSNot for Rosale