ASME_A112.6.7-2001.pdf

The American Society ofMechanical EngineersAN AMERICANNATI ON ALSTAN D AR DENAMELED AND EPOXYCOATED CAST IRON ANDPVC PLASTIC SANITARYFLOOR SINKS8ag35eAseNo reproduction or networking pemmitted without license from IHSNot or ResaleASMA112.6,7-2001Date of Issuance:June 29,2001This Standard will be revised when the Society approves the issuance ofa new edition.There will be no addenda or written interpretations of therequirements of this Standard issued to this edition.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria forAmerican National Standards.The Standards Committee that approved the code or standardwas balanced to assure that individuals from competent and concerned interests have had anopportunity to participate.The proposed code or standard was made available for public reviewand comment that provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not approve,rate,or endorseany item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted inconnection with any items mentioned in this document,and does not undertake to insure anyoneutilizing a standard against liability for infringement of any applicable letters patent,nor assumeany such liability.Users of a code or standard are expressly advised that determination of thevalidity of any such patent rights,and the risk of infringement of such rights,is entirely theirown responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not tobe interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued inaccordance with the established ASME procedures and policies,which precludes the issuanceof interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright2001byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSCopyright ASME IntomafionalProvided by IHS under license with ASMEAll Righ s ReservedNo reproduction or networking permitted without license from IHSPrintedFOREWORDThe American National Standards Committee A112 was organized on July 27,1955 forthe purpose of standardization of plumbing materials and equipment.The first organizationalmeeting was held on July 22,1958.At the meeting on May 1,1964,Panel No.21 wascreated to establish standards for roof drains,floor drains,backwater valves and otherdrainage specialties.Its scope was as follows:The recommendation of suitable existingstandards in cooperation with interested sponsors,or the development of adequate newstandards as needed for roof drains,floor drains,and other drains as used or installed inplumbing systems.The A112 Committee undergoing a number of organizational changes over the years iscurrently identified as ASME Standards Committee Al12.Al12 Panel 21 Working Groupswith the responsibility for drainage products were reorganized as Project Teams with sanitaryfloor sinks assigned to Project Team 6.7.The project team met twice for the purpose ofdeveloping this Standard including criteria from the International Association of Plumbingand Mechanical Officials(IAMPO)product standards PS-62,PS-83,and PS-84.Suggestions for improvement of this Standard will be welcomed.They should be sentto The American Society of Mechanical Engineers;Attn.:Secretary,A112 Committee;ThreePark Avenue;New York,NY 10016-5990.This Standard was approved as an American National Standard on January 17,2001.Copyright ASME IntomafionalProvided by IHS under license with ASMENo reproduction or networking permitted without license from IHS份or ResalASME STANDARDS COMMITTEE A112Standardization of Plumbing Materials and Equipment(The following is the roster of the Committee at the time of approval of this Standard.)OFFICERSP.J.Higgins,ChairS.A.Remedios,Vice ChairC.J.Gomez,SecretaryCOMMITTEE PERSONNELR.H.Ackroyd,Rand EngineeringJ.C.Aiello,Jacuzzi Whirlpool BathJ.A.Ballanco,JB Engineering Code ConsultingS.L.Cavanaugh,United AssociationA.Cohen,Arthur Cohen AssociatesN.Covino,A/ternate,American Standard,Inc.P.V.DeMarco,American Standard,Inc.G.S.Duren,Code Compliance,Inc.R.Emmerson,Chicago Faucets Co.F.C.Evans,Zin-Plas CorporationL.S.Galowin,National Institute of Standards and TechnologyC.J.Gomez,The American Society of Mechanical EngineersR.I.Greenwald,Sunroc CorporationG.Gress,Building Officials and Code Administrators International,Inc.P.J.Higgins,PJ Higgins Associates,Inc.D.E.Holloway,United States Testing Co.,Inc.M.Klimboff,ConsutantM.T.Kobel,IAMPOL.M.Kriegbaum,A/ternate,Underwriters Laboratories,Inc.J.W.Lauer,Sloan Valve Co.R.M.Martin,California Energy CommissionP.Meikle,Underwriters Laboratories,Inc.L.A.Mercer,Moen,Inc.S.Rawalpindiwala,Kohler Co.S.Remedios,Delta Faucet Co.J.A.Sargent,A/ternate,Kohler Co.G.L.Simmons,Charlotte Pipe and FoundryW.M.Smith,Jay R.Smith Industries,Inc.D.W.Viola,Plumbing Manufacturers InstituteR.E.White,Richard E.White AssociatesW.C.Whitehead,Plumbing Drainage InstituteCopyright ASME IntomafionalProvided by IHS under license with ASMENo reproduction or networking permitted without license from IHSNor Resale