pec_17E-2017.pdf

Date of Issue:December 2017 Affected Publication:API Specification 17E,Specification for Subsea Umbilicals,Fifth Edition,July 2017 Addendum 1 Delete the following from the cover:Effective Date:January 15,2018 In Section 1,Scope,on Page 1,delete the last sentence:If a product is supplied bearing the API Monogram and manufactured at a facility licensed by API,the requirements of Annex A apply.Delete Annex A in its entirety and replace with:This annex intentionally left blank.Specification for Subsea UmbilicalsAPI SPECIFICATION 17EFIFTH EDITION,JULY 2017ADDENDUM 1,DECEMBER 2017Special NotesAPI publications necessarily address problems of a general nature.With respect to particular circumstances,local,state,and federal laws and regulations should be reviewed.Neither API nor any of APIs employees,subcontractors,consultants,committees,or other assignees make anywarranty or representation,either express or implied,with respect to the accuracy,completeness,or usefulness of theinformation contained herein,or assume any liability or responsibility for any use,or the results of such use,of anyinformation or process disclosed in this publication.Neither API nor any of APIs employees,subcontractors,consultants,or other assignees represent that use of this publication would not infringe upon privately owned rights.API publications may be used by anyone desiring to do so.Every effort has been made by the Institute to assure theaccuracy and reliability of the data contained in them;however,the Institute makes no representation,warranty,orguarantee in connection with this publication and hereby expressly disclaims any liability or responsibility for loss ordamage resulting from its use or for the violation of any authorities having jurisdiction with which this publication mayconflict.API publications are published to facilitate the broad availability of proven,sound engineering and operatingpractices.These publications are not intended to obviate the need for applying sound engineering judgmentregarding when and where these publications should be utilized.The formulation and publication of API publicationsis not intended in any way to inhibit anyone from using any other practices.Any manufacturer marking equipment or materials in conformance with the marking requirements of an API standardis solely responsible for complying with all the applicable requirements of that standard.API does not represent,warrant,or guarantee that such products do in fact conform to the applicable API standard.All rights reserved.No part of this work may be reproduced,translated,stored in a retrieval system,or transmitted by any means,electronic,mechanical,photocopying,recording,or otherwise,without prior written permission from the publisher.Contact the Publisher,API Publishing Services,1220 L Street,NW,Washington,DC 20005.Copyright 2017 American Petroleum InstituteForewordThis standard was developed as an API recommended practice under the jurisdiction of the API Upstream SegmentExecutive Committee on Drilling and Production Operations.Standards referenced herein may be replaced by other international or national standards that can be shown to meetor exceed the requirements of the referenced standard.This standard is under the jurisdiction of API Subcommittee 17 on Subsea Production Systems.Nothing contained inany API publication is to be construed as granting any right,by implication or otherwise,for the manufacture,sale,oruse of any method,apparatus,or product covered by letters patent.Neither should anything contained in thepublication be construed as insuring anyone against liability for infringement of letters patent.This is the Fifth Edition.API Subcommittee 17 documents consist of the following:Recommended Practice 17A,Design and Operation of Subsea Production SystemsGeneral Requirementsand RecommendationsRecommended Practice 17B,Recommended Practice for Flexible PipeSpecification 17D,Specification for Subsea Wellhead and Christmas Tree EquipmentSpecification 17E,Specification for Subsea UmbilicalsStandard 17F,Specification for Subsea Production Control SystemsRecommended Practice 17G,Recommended Practice for Completion/Workover Riser SystemsRecommended Practice 17H,Remotely Operated Tools and Interfaces on Subsea Production SystemsSpecification 17J,Specification for Unbonded Flexible PipeSpecification 17K,Specification for Bonded Flexible PipeSpecification 17L1,Specification for Flexible Pipe Ancillary EquipmentRecommended Practice 17L2,Recommended Practice for Flexible Pipe Ancillary EquipmentRecommended Practice 17N,Recommended Practice for Subsea Production System Reliability and TechnicalRisk ManagementStandard 17O,Standard for Subsea High Integrity Pressure Protection Systems(HIPPS)Recommended Practice 17P,Design and Operation of Subsea Production SystemsSubsea Structures andManifoldsRecommended Practice 17Q,Recommended Practice for Subsea Equipment QualificationStandardizedProcess for DocumentationRecommended Practice 17R,Recommen