ANSI
C82.1-1985
R1992
C82
1985
I NOTICE OF I I ADOPTION I ANSI C82.1-1985 was adopted on 23 December 195 Department of Defense(DoD).The American Nat furnished the clearance required by existing x document are stocked at the Standardization D c 700 Robbins Avenue,Philadelphia,PA 19111-5C only.All other requestors must obtain copies ANS I 11 W.42nd Street New York,NY 10036 Title of Document:Standard for Ballasts for Date of Specific Issue Adopted:May 17,1985,C82.la-1990(C82.lb-1990(C82.l-1990(Releasing Non-Government Standards Body:ANSI Custodian:Navy-YD DISTRIBUTION STATEMENT A.unlimited.Approved for public ADOPTION NOTICE 2 23 December 1991:for ANSI C82.1-1985 i May 17,1985*!I and is approved for use by the mal Standards Institute has plations.Copies of the unents Order Desk,Bldg.4D,I c,for issue to DoD activitieis Irom:I!i Luorescent amps-Specifications kincluding Supplements inuary 22,1990),5bruary 21,1990),and inuary 22,1990)I 1 Military Coordinating Activity:Navy-YD(Project 6240-1303)I I FSC 6246 dease;distribution is i A N S I C82-L 85 072LiL.50 0032022 5 M Lamp type ANSI C82.1 a-1 991 Revision of ANSI C82.la-1990 Supplement to ANSI C82.1-1985 Minimum light output tolerances(percent)1 American National Standard 7 for ballasts for fluorescent lamps-specif cat ions(replacement for table 6)(Approved July 15,1991 Secretariat:National Electrical Manufacturers Association)This table replaces table 6 in ANSI C82.1-1985,and revises ANSI C82.1a-1990 Linear lamps 4,6,8WT5 14WT8 15WT8 14,15,20WT12 17,25,32,40WT8 30,40WT12 34WT12 0.800A and 1.OA T i 2 1.5A T12 and PG17 Circular lamps 20WT9 22,32,40WT9 32WT10 40WT1 O U-Shaped lamps 16,24,31WT8 40WT12-10-1 o-1 o-1 o-7.5-7.5-1 5-5-5-1 O-10-10-10-7.5-7.5 A ballast that is rated for use with both a 40-watt and a 34-watt lamp and meets the 40-watt lamp requirements need not be testedon a34-watt lamp._ An American National Standard implies a consensus of those substantially concerned with its scope and provisions.An American National Standard is intended as a guide to aid the manufacturer,the consumer,and the general public.The existence of an American National Standard does not in any respect preclude anyone,whether he has approved the standard or not,from manufac-turing,marketing,purchasing,or using products,processes,or procedures not conforming to the standard.American National Standards are subject to periodic review and users are cautioned to obtain the latest editions.The American National Standards Institute does not develop standards and will in no circumstances give an interpretation of any American National Standard.Moreover,no person shall have the right or authority to issue an interpretation of an American National Standard in the name of the American National Standards Institute.CAUTION NOTICE:This American National Standard may be revised or withdrawn at any time.The procedures of the American National Standards Institute require that action be taken to reaffirm,revise,or withdraw this standard no later than five years from the date of approval.Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute.I Copyright O 1991 by American National Standards Institute,11 West 42nd Street,New York,N.Y.10036 ANS14Ci191110-i-,-,-ANSI C82-3 85 0724350 0032023 7 Voltage across dummy load(vo It s)ANSI C82.1 b-1991 Revision of ANSI C82.lb-1990 Supplement to ANSI C82.1-1985 Voltage during operations(volts)American National Standard for ballasts for fluorescent lamps-specifications-(replacement for table 7)Approved July 15,1991 Secretariat:National Electrical Manufacturers Association Page 1 of 2 pages This table replaces table 7A in ANSI C82.1 b-1990.(Table 7B is not revised.)Table 7A-Cathode voltage limits for rapid start lamps Lamp type Linear lamps 17,25,32,40WT8 30,34,40WT12 40WT1 O 0.800A and 1.OA TI 2 1.5A T12 and PG17 Circular Lamps 20WT9 22,32,40WT9 32,40WT10 U-Shaped Lamps 16,24,31WT8 40WT12 Dummy load*(ohms)11.o fO.1 9.6f0.1 9.6 f 0.1 3.2 f 0.05 3.2 f 0.05 9.6 f 0.1 9.6 f 0.1 9.6 f 0.1 1 1.o f 0.1 9.6 f 0.1 I 4.4 4.0 4.0 4.0t 4.3 4.0 4.0 4.0 4.4 4.0 Where one ballast winding operates two cathodes in parallel,the dummy load resistor should be half the value given.t Maximum voltage is 4.3V if the filament resistance exceeds 150%of the stated objective.See ANSI C82.2-1984 for method of measurement.An American National Standard implies a consensus of those substantially concerned with its scope and provisions.An American National Standard is intended as a guide to aid the manufacturer,the consumer,and the general public.The existence of an American National Standard does not in any respect preclude anyone,whether he has approved the standard or not,from manufac-turing,marketing,purchasing,or using products,processes,or procedures not conforming to the standard.American National Standards are subject to periodic review and users are cautioned to obtain the latest editions.The American National Standar